Installation - Hoshizaki IM-21CLE Bedienungsanleitung

. This booklet is an integral and essential part of the product
and should be kept and preserved by the user. Please read
carefully the guidelines and warnings contained herein as
they are intended to provide the installer/user with essential
information for the proper installation and the continued safe
use and maintenance of the product. Please preserve this
booklet for any further consultation that may be necessary.
2. This is a commercial icemaker, and should be destined only
to be used for the purpose for which it has been expressly
designed. Any other use should be considered improper
and therefore dangerous. The manufacturer will not be held
liable or responsible for any damage caused by improper,
incorrect and unreasonable use.
I. INSTALLATION INSTRUCTIONS
The installation must be carried out by qualified personnel,
in accordance with current regulations, according to the
manufacturer's instructions.
1. UNPACKING
Children should not be allowed in reach of the packaging
elements (plastic bags and expanded polystyrene) as they are
potential sources of danger.
Remove shipping carton, tape(s) and packing. If packing
material is left in the icemaker, it will not work properly.
Handle
Front Panel
(Lower)
Power Cord
) After removing the packaging, make sure that the icemaker is in
good condition. If in doubt, please do not use the equipment but
apply to professionally qualified personnel.
2) Remove shipping tape holding the Door and Front Panel.
3) Remove the protective plastic film from the exterior. If the icemaker
is exposed to the sun or to heat, remove the film after the icemaker
cools.
4) Remove the package of accessories, and check the contents:
a) Installation Kit (Air-Cooled)
Inlet Hose
Outlet Hose
Installation Kit (Water-Cooled)
Inlet Hose
Outlet Hose
/2-3/4 Nipple
b) Scoop
c) Adjustable Leg (Except IM-2)
* Provided for Europe/General(G50)/Australia only
5) Remove shipping tape holding the Bin Control Switch by opening
the Bin Door and reaching in (see Fig. 2).
IMPORTANT
WARNING
WARNING
CAUTION
Top Panel
Front Panel
(Upper)
Storage Bin
Slope
Bin Door
Condensing Unit
Louver
(Air-cooled Model)
Air Filter
(Air-cooled Model)
Fig. 1


2
2
2

4*
[IM-2/25/30]
Bin Control
Switch
Air Filter
(Air-cooled Model)
[All models except IM-2/25/30/45CLE]
Top Panel
2. LOCATION
. This icemaker is not intended for outdoor use. Normal
operating ambient temperature should be within °C to 40°
C. Normal operating water temperature should be within 5°
C to 35°C. Operation of the icemaker, for extended periods,
outside of these normal temperature ranges may affect
production capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for
the equipment at normal counter top height.
4. Allow 5 cm clearance at rear, sides and top for proper air
circulation and ease of maintenance and/or service should
they be required.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top of the icemaker or in front of the
Louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero (see "II. 2. PREPARING
THE ICEMAKER FOR LONG STORAGE").

3. INSTALLATION

* Incorrect installation can cause harm to people, animals or things,
for which the manufacturer cannot be held responsible.
* Place the icemaker in the selected permanent site.
4. ELECTRICAL CONNECTIONS
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national
and local electrical code requirements. To prevent possible
severe electrical shock to individuals or extensive damage to
equipment, install a proper earth wire to the icemaker. Remove
the plug from the mains socket before any maintenance, repairs
or cleaning is undertaken.

ENGLISH
[IM-45CLE-25]
Bin Door
Bin Control
Fig. 2
Switch
IMPORTANT
WARNING
Air Filter