Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Solar Stopwatch incl. Temperature,
Humidity
Item no. 86 07 47
1.
Intended use
This stopwatch features lap count and split time functions. The stopwatch also displays time and date and
includes an alarm clock and a countdown function. Moreover, it can also indicate temperature, humidity, heat
index and dew point. It is powered by a solar module on the front panel of the stopwatch, and by a button cell
battery. The product has a background lighting function.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
2.
Delivery content
•
Stopwatch
•
Button cell battery (CR2032)
•
Operating instructions
3.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
Persons / Product
•
The product is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous playing material
for children.
•
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
•
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
•
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
Batteries
•
Correct polarity must be observed while inserting the battery.
•
The battery should be removed from the device if it is not used for a long period of time to avoid damage
through leaking. Leaking or damaged batteries might cause acid burns when in contact with skin, therefore
use suitable protective gloves to handle corrupted batteries.
•
Batteries must be kept out of reach of children. Do not leave batteries lying around, as there is risk, that
children or pets swallow them.
•
Batteries must not be dismantled, short-circuited or thrown into fire. Never recharge non-rechargeable
batteries. There is a risk of explosion!
Miscellaneous
•
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
shop.
•
If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4.
Operating elements
1
Multiple functions are allocated to some of the buttons; depending on the setting you are
modifying, their functions may vary.
When pressing a button, press it briefly once. With certain settings it will be necessary to hold
the button after pressing it down. It will then take approx. 2 seconds until the required function
is actioned.
You can accelerate number inputting by pressing and holding the Start/Stop button (5) when
setting numbers.
1.
Display
2.
Lap/Reset button
3.
Recall button
4.
Mode button
5.
Start/Stop button
6.
Solar cell
7.
Light button
6
7
5.
Replacing batteries
1.
Remove the screws from the back of the product.
2.
Remove the battery compartment cover.
Version 05/12
3.
Remove the button cell and insert one new button cell battery (CR2032), observing the correct polarity. The
positive terminal must point outwards.
4.
Close the battery compartment cover and tighten the screws again.
6.
Operation
When no buttons are pressed for 30 seconds, all settings are automatically saved.
Background lighting
Press the Light button (7) to activate the background lighting for five seconds.
Clock mode
The clock mode shows time and date.
a
b
c
Setting date and time
1.
To set the time (c) and date, switch to the clock mode using the Mode button (5).
2.
Press and hold the Recall button (3) until the seconds digits start flashing. The weekday indicator (b) will
switch automatically to the year.
3.
Press the Start/Stop button (5) once to set the seconds digits to zero.
4.
Press the Lap/Reset button (2) to set the minutes.
5.
Press the Start/Stop button (5) repeatedly to set the minutes in single increments. Press and hold the Start/
Stop button (5) to accelerate number inputting.
6.
With the Lap/Reset button (2), switch to the hour setting and set the required hour using the Start/Stop
button (5). Proceed in a similar fashion with setting the year (b), the month (a) and the day (e).
7.
After setting the day, the display will switch to the 12/24-hour format setting. Press the Start/Stop button
(5) to toggle between both format settings.
8.
Save your settings and exit with the Mode button (4) or the Recall button (3).
Touch tones
In clock mode, press the Lap/Reset button (2) or the Start/Stop button (5) to turn the touch tones on or off. With
touch tones turned on, a musical note icon (d) is shown on the top right of the display.
Temperature and humidity mode
a
1.
To show temperature (b) and air humidity (a), switch to the temperature and humidity mode using the Mode
button (4).
2.
Press the Lap/Reset button (2) to toggle between Celsius (°C) and Fahrenheit (°F).
Heat index mode
a
1.
To show the heat index (perceived temperature/windchill factor) (a), switch to the heat index mode using
the Mode button (4).
2.
Press the Lap/Reset button (2) to toggle between Celsius (°C) and Fahrenheit (°F).
Dew point mode
a
1.
To show the dew point (a), switch to the dew point mode using the Mode button (4).
2.
Press the Lap/Reset button (2) to toggle between Celsius (°C) and Fahrenheit (°F).
d
e
b
Werbung
Inhaltsverzeichnis
