Before Use - Powerfix Z29798 Bedienungsanleitung

Safety instructions / Before use / Use
Do not step off the side of a ladder
Only one per ascendable leg of the ladder / stepladder
Do not use the ladder as a bridge
Do not stand on the top tread
Ensure that no part of the ladder comes into contact
with a live cable
Face ladder when ascending or descending ladder

Before use

Q
j
A void damaging ladders when transporting them on a roof rack or on the
back of a lorry. Ensure that the ladder is appropriately fastened in place.
j
R emove any foreign material such as wet paint, dirt, oil or snow from the
multipurpose scaffold / ladder.
j
L ock all doors and windows (but not emergency exits) in the working
area of the multipurpose scaffold / ladder.
Use
Q
Assembling the multipurpose scaffold / ladder
Q
note: If possible have a second person help you with the assembly.
1. Mount the short base stabiliser
the long base stabiliser to the wide ladder section
1
Figure A.
6 GB/IE/CY
4 to the narrow ladder section 2
, as shown in
3
2. Attach the working platform
ladder sections 2 and
note: Ensure that the maximum standing height of 100 cm is not
exceeded (Figure F).
3. Insert the plastic sleeve
narrow section .
3
4. Insert the short threaded rod
narrow ladder section
plain washer to the wide ladder section
15
5. Connect the diagonal struts
6. Attach the diagonal struts
wing nuts .
7
Disassembling the multipurpose scaffold / ladder
Q
j
D isassemble the multipurpose scaffold / ladder in the reverse order to that
described in the section "Assembling the multipurpose scaffold / ladder".
Assembling the standing ladder
Q
J
A void any tasks in which a lateral load is placed on the standing ladder,
e.g. drilling sideways into solid material (e.g. masonry or concrete).
J
D o not use the standing ladder as a means of ascending on to another
level.
1. Mount the short base stabiliser
the long base stabiliser
Figure A.
2. Push the narrow ladder section
wide ladder section
engage in the guide groove (Figure G).
3. Guide the threaded end piece of the safety stay
on the narrow ladder section
4. Fix the safety stay
18
from the inner face of the stile on to the threaded end piece of the
safety stay (Figure H).
18
Disassembling the standing ladder
Q
j
D isassemble the standing ladder in the reverse order to that described in
the section "Assembling the standing ladder".
Assembling the leaning ladder
Q
J
A void any tasks in which a lateral load is placed on the leaning ladder,
e.g. drilling sideways into solid material (e.g. masonry or concrete).
1. Attach the long base stabiliser
shown in Figure J.
2. Push the narrow ladder section
wide ladder section
ladder section can fit over the second rung of the wide ladder
2
section (Figure L).
3
3. Hold the leaning ladder in a vertical position in front of the wall or the
object against which the leaning ladder is to be used. Disengage the
locking hooks and slide the narrow ladder section
necessary until it reaches the desired climbing height (Figure M).
4. At that point fit the locking hooks over the rung of the wide ladder
section . Place the leaning ladder carefully against the wall or the
3
object (Figure N).
Disassembling the leaning ladder
Q
j
and D isassemble the leaning ladder in the reverse order to that described in
the section "Assembling the leaning ladder".
to the rung at the desired height on both
5
3 (Figure B).
to the narrow ladder section
16
each with a plain washer
11
and the long threaded rod
2 12
.
3
with the slotted bolt and the locknut
6 8
6 to the ladder sections 2
to the narrow ladder section
4
to the wide ladder section
1
as far into the guide angle of the
2
3 as possible until the guide pins on both sides
through the hole
18
.
2
in place by screwing the plastic nut
to the wide ladder section
1
as far into the guide angle of the
2
as possible until the locking hooks on the narrow
3
2
and the wide
2
to the
15
each with a
.
13
and 3 using the
and
2
, as shown in
3
tightly
17
, as
3
as far upwards as