Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
LED Module 3W
Item no. 17 60 06
Prescribed use
The "LED Module 3W" is an illuminant with a heat dissipating housing and an integrated reflector ready
for operation. The light is generated by a powerful Luxeon® LED. The product may only be connected to
a suitable constant-current source with a maximum of 700mA. It must not be connected to conventional
low-voltage or high-voltage halogen systems.
Please take note of all safety instructions and installation notes in these operating instructions.
The product meets the requirements of the current European and national guidelines. All company
names and product designations contained herein are trademarks of the respective owners. All
rights reserved.
Scope of delivery
• LED module 3W
• Installation material
• Operating manual
Technical specifications and features
• Connection to a constant-current source with a maximum of 700 mA, observe the correct polarity!
(must not be connected to low-voltage/high-voltage halogen systems)
• LED module with a heat dissipating housing and an integrated reflector ready for operation
• Rotating/swinging
• Integrated Luxeon® LED, 3W
• Light current at 700 mA: 65lm
• Service life of the LED: about 50,000h
• The density of light depends on the distance to the illuminated surface (0.5m= 6500lux, 1m = 2000lux,
2m= 850lux)
• Opening angle: about 20°
• Feed cables: red = plus/+, black = minus/-, length: about 20cm, cross section: 0.5mm²
• Temperature of the lamp body at a permanent operation: about 30° above ambient temperature
• Maximum admissible temperature of the lamp body: 65°C
Safety instructions
In case of any damages which are caused due to failure to observe these operating
instructions, the guarantee will expire! We do not assume any liability for resulting
damages!
Nor do we assume liability for damage to property or personal injury, caused by
improper use or the failure to observe the safety instructions! The guarantee will
expire in any such case!
• The unauthorized conversion and/or modification of the product is inadmissible because of safety
reasons. This module is a "non-CE-checked" component. The utilisation must comply with the CE
norms.
• The product may only be operated at a constant-current source (control gear) with a maximum current
of 700mA.
• The product is not a toy. Be especially careful when children are around.
The product must be mounted out of reach of children.
• Never look directly into the light beam and never direct the lamp to people or animals. There is a risk
of damages to the retina.
• Do not touch the product during operation: risk of burns! Have the product cool down long enough
before you rotate or replace it etc.
• The product must not get damp or wet, it is suitable for indoor use only.
• Make sure when mounting, that the connecting cable is not bent, jammed or damaged by sharp edges.
Install the connecting cable in such a way that it does not touch the LED module (danger of fire).
• Install the LED module in such a way as to allow for a sufficient safety distance to flammable surfaces/
materials (wood, carpets, electrical cables, insulation material etc.). The distance must be 10cm
minimum to all sides. Never cover the unit.
Before mounting the product in flammable surfaces (e.g. wooden ceilings) ask the correspondent
manufacturer/seller if the installation and the operation of the LED module is possible under these
conditions. If it is not possible, the LED module must not be installed.
The LED module can be mounted in or on materials with unknown properties as to flammability, if it is
guaranteed, through appropriate measures, that the temperature on the mounting surfaces does not
exceed 90°C in normal operation and 115°C in case of a fault (unless marked with "MM").
No insulation material must be in the direct proximity of the LED module, as this would cause heat to
accumulate. There is a danger of fire!
Between the LED module and the control gear or other lighting fixtures, there must be at least 20cm.
Danger of overload; danger of fire!
• The radiant heat of the LED module can, during operation, affect the material and the colour of the
surfaces. It is recommended, at any rate, to check the behaviour of surfaces at the place of installation
before the final installation.
• A minimum clearance of 50cm must be kept between the outlet of the light beam from the LED module
and the illuminated surface. Otherwise, there is a danger of fire! Never direct the light beam on easily
flammable objects (e.g. curtains).
• In industrial facilities, the safety regulations laid down by the professional trade association for electrical
equipment and facilities must be adhered to.
• When installing the product and operating tools observe the corresponding operating and safety
instructions.
• Do not leave packaging material unattended. It may become dangerous playing material for children!
• Handle the product carefully and do not drop it, knocks, blows or even a fall from a low height can
w w w. c o n r a d . c o m
Mounting
Version 05/07
• The place of installation must be firm and stable. Think about the arrangement of the LED module, for
• Mount a suitable control gear (constant-current source).
• As illustrated above, the aluminium strips must be bent accordingly.
• Put the brackets together as shown. When mounted to the wall or ceiling, the swinging range is about
• Mount the LED module to the ceiling etc. with a screw. Place the two feed cables in such a way that they
Maintenance, handling, operation
The product does not require any maintenance. You should never take it apart..
You can remove dust from the lens of the LED module from time to time with a clean, soft, and dry cloth.
Remove dust from the heat dissipator with a dry, long-haired brush.
Disposal
© 2007 by Conrad Electronic SE. Printed in Germany.
damage it.
Take note of all the safety notes in these operating instructions!
example at the ceiling, beforehand.
The LED module must only be operated at a constant- current source (700mA max.).
It must not be connected to a conventional halogen transformer or even to the mains
voltage!
Otherwise, the LED will be destroyed - loss of guarantee/warranty!
Do not bend them more or they might break.
60°.
cannot be damaged by the support fixture.
For connecting the two feed cables in the LED module (red = plus/+, black = minus/-) suitable cables
are necessary (minimum cross section 0.5mm², if the lines are longer, use greater cross sections).
Connect the cables with a terminal strip for example, or solder the cables, use stocking tubes to prevent
a short-circuit.
Before cleaning the product, switch off the power source and wait at least 20 minutes to let
the LED module cool down.
Please dispose of the unserviceable device according to the current statutory require-
ments.
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-
Straße 1, D-92240 Hirschau/Germany.
These operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifiations.
Werbung
