Gude Expert Power Control 1104 Anleitung Seite 54

Spezifikationen
snmp port set {ip_port}
snmp port show
snmp snmpget enabled set {OFF=0|ON=1}
snmp snmpget enabled show
snmp snmpset enabled set {OFF=0|ON=1}
snmp snmpset enabled show
snmp snmpv2 enabled set {OFF=0|ON=1}
snmp snmpv2 enabled show
snmp snmpv2 public set "{text}"
snmp snmpv2 public show
snmp snmpv2 private set "{text}"
snmp snmpv2 private show
snmp snmpv3 enabled set {OFF=0|ON=1}
snmp snmpv3 enabled show
snmp snmpv3 username set "{text}"
snmp snmpv3 username show
snmp snmpv3 authalg set {NONE=0|MD5=1|
SHA1=2|SHA256=3|SHA384=4|SHA512=5}
snmp snmpv3 authalg show
snmp snmpv3 privalg set {NONE=0|DES=1|
3DES=2|AES128=3|AES192=4|AES256=5|
AES192*=6|AES256*=7}
snmp snmpv3 privalg show
snmp snmpv3 authpasswd set "{passwd}"
snmp snmpv3 privpasswd set "{passwd}"
snmp snmpv3 authpasswd hash set "{passwd}"
snmp snmpv3 privpasswd hash set "{passwd}"
snmp trap type set {NONE=0|V1=1|V2=2|V3=3}
snmp trap type show
snmp trap receiver {trap_num} set "{dns_name}"
snmp trap receiver {trap_num} show
syslog
syslog enabled set {OFF=0|ON=1}
syslog enabled show
syslog server set "{dns_name}"
syslog server show
system
system restart
system fabsettings
system bootloader
system flushdns
system uptime
vt100
vt100 echo set {OFF=0|ON=1}
vt100 echo show
vt100 numeric set {OFF=0|ON=1}
vt100 numeric show
vt100 reset
Hinweise
1. Legacy - Der Befehl ist von einer neueren Version abgelöst worden
2. Befehl kann auf allen Ebenen ausgeführt werden
3. Die Ausgabe kann 2 Zeilen umfassen - die erste Zeile zeigt den aktuellen Zustand,
die zweite Zeile den Status nach einem Neustart
4. Die Ausgabe kann mehrere Zeilen umfassen
5. Bitte die Energie Sensor Tabelle konsultieren, um den richtigen Index zu finden
6. Bitte die Tabellen Externer Sensor Feld und Externer Sensor Typ konsultieren,
um den richtigen Index zu finden
Energie Sensor Tabelle "{energy_sensor}"
Index Beschreibung
0 Absolute Active Energy
Expert Power Control 1104 / 1105
sets SNMP UDP port
shows SNMP UDP port
enables SNMP GET cmds on/off
show if SNMP GET cmds are enabled
enables SNMP SET cmds on/off
show if SNMP SET cmds are enabled
enables SNMP v2 on/off
show if SNMP v2 is enabled
enables SNMP v3 on/off
show if SNMP v3 isenabled
sets SNMP v2 public cummnity
shows SNMP v2 public community
sets SNMP v2 private community
shows SNMP v2 private community
sets SNMP v3 username
shows SNMP v3 username
sets SNMP v3 authentication
show SNMP v3 authentication algorithm
sets SNMP v3 privacy algorithm
show SNMP v3 privacy algorithm
sets SNMP v3 authentication password
sets SNMP v3 privacy password
sets SNMP v3 authentication hashed password
sets SNMP v3 privacy hashed password
sets type of SNMP traps
show SNMP trap type
sets address and port of SNMP trap receiver
{trap_num}
show address and port of SNMP trap receiver
{trap_num}
enters cmd group "syslog"
enables syslog msgs on/off
show if syslog enabled
sets address of syslog server
shows address of syslog server
enters cmd group "system"
restarts device
restore fab settings and restart device
enters bootloader mode
flush DNS cache
number of seconds the device is running
enters cmd group "vt100"
sets console echo state
shows console echo state
sets numeric mode
shows numeric mode state
resets terminal
Einheit
Wh
54
© 2018 Gude Analog- und Digitalsysteme GmbH