Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
Motion detector 180°
Item-No. 62 51 45
Intended use
This motion detector offers a horizontal detection range of 180° and a max. detection range of
up to 12 metres. Additionally, you can adjust the motion detection from 5 seconds to max. 7
minutes (+/- 2 min.) and the brightness sensitivity from approx. 5 Lux up to daylight brightness
and the motion detection sensitivity, for this rotary knobs are placed beneath the housing of the
motion detector. The motion detector works with a power supply of 230 V/AC 50 Hz. Omic load
up to a maximum of 1200 Watts and inductive load of up to a maximum of 500 Watts can be
connected and switched.
The motion detector is designed for outdoor use (IP44).
Do not operate the product in any other way than that described above. This could lead to damage
to the product, which may give rise to hazards such as short circuit, fire and electric shock. The
product must not be modified or converted. Always observe the safety instructions included in
these operating instructions. Read the operating instructions carefully and keep them for later
reference.
Explanation on the symbols
A lightning-bolt symbol in a triangle indicates a health hazard, e.g. danger of electric
shock.
The exclamation mark in a triangle indicates a particular risk during handling, operation
and control.
The „hand" symbole indicates special tips and operating notes.
Safety instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume liability for consequential damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. The warranty will
be void in such cases.
Dear customer: The following safety instructions and hazardnotes are intended not only
the protection of the device but also for the protection of your health. Please read the
following points carefully:
• The motion detector is suitable for use on a vertical wall in dry indoors.
• If the motion detector and the junction box are brought from a cold into a warm room
(e.g. for transport reasons), it is possible that condensation water may develop. This
might cause a lethal electric shock! Therefore, allow the components to reach room
temperature before installing and operating them.
• The unauthorised conversion and/or modification of the unit is not permitted because
of safety and approval reasons (CE).
• Do not bend the connecting cables, and do not put any heavy objects on them.
• Only a person knowledgeable of the specifications (VDE) and the dangers should install
this product.
• Ensure that all the electrical connections and connection cables between the various
devices and any extension cables comply with regulations and also comply with the
operating instructions.
• Live components may be exposed, if the covers are opened or parts removed (unless
this can be done without tools). Further, the connection points may be live. If the
appliance needs to be opened for calibration, servicing, repair or to replace parts or
circuit boards, it must be disconnected first from all sources of current . If servicing or
internal repairs are necessary, this must be carried out by a specialist who is familiar
with the risks involved and with the relevant regulations.
• A safe operation can no longer be assumed, if:
- the device shows visible signs of damage,
- the device no longer functions and
- if the device was stored under adverse conditions for a long period of time or
- after heavy loading during transport.
• Please contact an expert, if it is no longer safe to use the unit or you have doubts about
the function of the product. Never try to repair the product or replace damaged cables
yourself.
• Keep electrical devices out of the reach of children. Take particular care when children
are around, as they may try to stick objects into the unit through the openings in the
housing. There is danger of a life-threatening electric shock.
• The motion detector must only be operated with a voltage of 230 V/AC.
• Never position the motion switch close to combustible or easily inflammable materials,
e.g. curtains.
• Never expose the motion detector to extremely high or extremely low temperatures,
humidity or vibrations.
• Strong mechanical tensile or compressive forces can damage the motion detector.
• The product is designed for outdoor use (IP44).
• Observe that the corresponding fuse is removed from the fuse box (or switch the circuit
www.conrad.com
breaker) prior to mounting and connecting.
• Devices operated using the mains voltage must be kept out of the reach of children.
Therefore, be especially careful when children are around.
Version 08/09
• Do not leave packaging material lie around unattended, they may become dangerous
playthings for children.
• Consider the current legal framework before you install the motion detector.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Materials are to be
observed.
• In schools, educational centres, hobby and self-help workshops the operation of the
product is to be supervised by trained employees.
Functional description
This motion detector responds to heat radiation which is emitted by objects entering the
detection area of the motion detector. The motion detector must „see" the area it is to keep under
surveillance. Heat radiation travels in straight lines but is obstructed, for example, by glass or
other fixed objects. Before mounting, therefore, pay attention to this, or other problem sources.
If someone enters the detection area of the motion detector, the electric consumer connected to
it is switched on and, after a certain period switched off again automatically. In addition, the
ambient brightness, at which the motion shall be activated, can be adjusted.
Product Description
1) Diffuser lense
2) Adjustment control „SENS, TIME, LUX"
3) Locking screw for adjustment element
4) Cable feedthrough
5) Mounting holes
6) Housing screw
Werbung
Inhaltsverzeichnis
