Operation - HQ Power VDP1401RGLD5 Bedienungsanleitung

res sult in serious in
• For r truss-mountin
the e (folded) brack
• Adj just the desired
• Ma ke sure there is
b) DMX- -512 connectio
• Wh hen applicable, c
and d the other side
VD DP1401RGLD5'
scr reened cable wit
• A D DMX terminator
or is in an electrica
dig gital control sign
res sistor between p
in t the chain.
c) gener ral
• Ma ke sure there is
coo oling.
• Hav ve a qualified e
• Co nnect the devic
• The e installation ha
7. Op eration
Refer to t the illustrations
• Make e sure the laser
laser r projector. Inse
• To tu urn on the laser
turns s on.
• The l aser can operat
Sound c ontrolled mod
• Set t all DIP switche
• Set t the microphon
DMX con ntrolled mode
• All DMX-controlled
sig nals. This digita
the e DMX controller
ind dividual address
• Wh hen all devices h
par rticular channel
sim multaneously. If
num mber. Changing
• In case of the 5-ch
1 ( CH1~5), the se
• Use e the DIP switch
• Ref fer to the table
Ch hannel DMX-5
CH1 102
204
10.01.20 011
njuries.
g, use an appro opriate clamp (n
et.
d inclination ang gle via the moun
s no flammable material within
on
connect an XLR cable to the fem
e to the male 3- pin XLR input o
's can be linked through serial
th XLR input an d output connec
is recommende ed for installatio
ally noisy enviro onment (e.g. di
nal by electrical noise. The DMX
pins 2 and 3, wh hich is then plug
s no flammable material within
lectrician carry out the electric
e to the mains w with the power
as to be approve ed by an expert
s on page 2 of th his manual.
projector is tur ned off. Insert t
ert the other end d of the power c
projector, use t the on/off switc
te in two modes s: sound contr
de
es [4] to the OF FF position to en
ne [2] sensitivit ty with the sens
d devices need a a digital start ad
al start address is the channel n
r. The same sta arting address ca
can be set for every device.
have the same a address, all the
. In other words s: changing the
you set individ ual addresses, e
g the settings of f one channel w
hannel VDP140 01RGLD5, you
econd unit to 6 ( (1 + 5) (CH6~1
hes [4] to set t he appropriate
switch
value
below for an ov verview of the c
512 value
0 ~ 50 So und active
51 ~ 101 Aut to
2 ~ 152 Se lect pattern mo
153 3 ~203 Co ntrol mode
4 ~ 255 No output
VDP1401 RGLD5
not incl.) and fit
nting bracket an
a 50cm radius
male 3-pin XLR
f the VDP1401
linking. The link
ctors.
ons where the D
scos). The term
X terminator is s
gged into the XL
a 50cm radius
al connection.
plug. Don't con
t before the dev
the power plug
cable into the m
ch [7] and turn
rolled or DMX c
nable sound con
sitivity knob [3]
ddress so that t
number from w
an be used for a
units will "listen
settings of one
each device will
will only affect th
will have to set
10), the third to
DMX address.
1 2 2 3 4
1 2 2 4 8
ontrol signals p
Control Pr
de
5
an M10 bolt th rough the centr
nd tighten the b racket screws.
of the device.
output of a con ntroller (not incl
1RGLD5. Multip le
king cable shou ld be a dual cor
DMX cable has to o run a long dis
minator prevents s corruption of t
simply an XLR p plug with a 120Ω
LR output socke et of the last dev
of the device an nd there is suffi
nect it to a dim ming pack.
vice is taken into o service.
into the power input [8] of the
mains.
the safety key. The power LED
controlled mod de.
ntrolled mode.
].
he correct devic ce responds to t
hich the device starts to "listen
a whole group o of devices or an
n" to the contro ol signal on one
e channel will af ffect all devices
"listen" to a se eparate channel
he device in que estion.
the start addre ess of the first u
11 (6 + 5) (CH H11~15), and so
5 5 6 7 8 8 9
1 6 32 64 12 28 256
er channel.
rograms
re of
.)
re,
tance
the
Ω
vice
cient
e
D [1]
the
n" to
unit to
o on.
man nv
©Vellem