Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
GB
Ceiling-Mounted Motion Detector
("Master")
Intended use
The product consists of a controller and a motion detector.
The motion detector's integrated PIR sensor responds to temperature changes within
the detection range, e.g. when a person enters the detection range.
It then activates the output of the controller, whereby e.g. a light or other load is
switched on for an adjustable amount of time.
The motion detector is intended for installation in a room ceiling.
One or more buttons can be connected to the controller of the motion detector to be
able to activate a connected light manually (for the duration of the time setting on the
motion detector).
As a feature, a total of 6 motion detectors can be connected to the control device: the
included motion detector and 5 additional ones (available as accessories).
The provided motion detector is used as the "master"; only this allows start-up time
setting and brightness control.
The adjustment of the sensitivity is possible both on the "master" motion detector
and on all optional "slave" motion detectors.
Any other use than that described above may damage the product. Moreover, this
may give rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the
product may be modifi ed or converted!
Always observe the safety instructions and all other information included in these op-
erating instructions. Read the operating instructions carefully and keep them safe for
later reference.
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owner. All
rights reserved.
Package Contents
• Controller with pre-installed PIR connection cable
• Motion detector ("Master")
• Plastic cover for limiting the PIR sensor opening angle
• Operating Instructions
Explanation of the Symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specifi c risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
The home technology brand for the entire house. More information at www.sygonix.com
Safety Instructions
Read the complete operating manual carefully before using the product,
as it contains important information about the correct installation and
operation.
The warranty will be void in the event of damage caused by failure to ob-
serve these safety instructions! We do not assume any liability for any
consequential damage!
We do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions! The
warranty will be void in such cases!
Caution!
This device should be installed only by people with relevant electrotech-
nical knowledge and experience!
With an improper installation, you risk:
- Your own life;
- The life of the user of the electrical system.
With an improper installation, you risk severe material damage, e.g. through
fi re. You face the risk of personal liability for damage to people and material.
Contact an electrician!
• The unauthorised conversion and/or modifi cation of the product is not al-
lowed for safety and approval reasons (CE).
• The product is not a toy and must be kept out of the reach of children! There
is a risk of a lethal electric shock!
• The controller may be operated only on the mains voltage (see section
"Technical Data"). Never try to operate the product at another voltage, as
this will cause its destruction.
• The controller complies with protection class II.
• The entire product is to be installed and used only in dry, enclosed indoor
spaces. The product must not get damp or wet as this may damage it; dan-
ger of a fatal electric shock!
• Do not use this product in rooms or under adverse ambient conditions
where combustible gases, vapours or dust are or may be present! There is a
risk of explosion!
• The product must not be exposed to extreme temperatures, strong vibra-
tions or heavy mechanical stress.
• If you have reason to assume that safe operation is no longer possible,
disconnect the product immediately and secure it against accidental opera-
tion. After this, let an expert check the product.
It can be assumed that safe operation is no longer possible if:
- the product shows visible signs of damage,
- the product does not work at all or works poorly (fl ickering light, leaking
smoke or a smell of burning, the light fl ickers, audible cracking noises, dis-
colouration to the product or the adjacent surfaces.)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around since it could be-
come a dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operating
Facilities are to be observed!
• If you have any questions that are not answered in this manual, please con-
tact our technical service or another specialist.
Werbung
Inhaltsverzeichnis
