Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Preparations for Installation
The product may only be installed and mounted by a qualifi ed technician (e.g.
electrician), who is familiar with the relevant regulations (e.g. VDE, German
electrical wiring regulations)!
Improper work, carried out on the mains voltage, endangers not only your
own life but also the life of others!
If you do not have the expertise required for the installation, do not install it
yourself but ask a qualifi ed technician.
Observe the safety instructions!
• Only install the LED spotlight on a stable surface. Use screws and plugs that are suitable for
the surface.
• The LED spotlight must be protected on the sub-distribution board by a 10/16A fuse. An earth
leakage circuit breaker must be installed before this (FI protective switch).
• The LED spotlight must be disconnected from the power supply during installation. It is not
suffi cient to just turn off at the light switch!
Turn the power off and ensure that none of the poles is carrying a current by removing the
electric circuit's fuse, or switching off at the circuit breaker. Secure it against unauthorised
reconnection, e.g., with a danger sign. In addition, switch off the appropriate earth-leakage
circuit breaker.
• Check that the mains connection is current free with a suitable tester.
Only use a cable for the mains connection that is suitable for being permanently laid
outdoors.
Installation
Pay attention to the information in the chapter "Preparations for Installation".
• Fasten the mounting bracket for the LED spotlight using at least two screws at a suitable
location on the wall. Depending on the installation location, suitable screws and, if necessary,
wall plugs are to be used.
When drilling the mounting holes or screwing into place, take care that no existing
electrical cable, gas or water pipes are damaged!
• The ideal installation height is between 2.5 and 3 m, depending on where it is installed, and
the ambient conditions (position of the area to be lit).
• Remove the installation box cover on the back of the LED spotlight, by unscrewing all four
fi xing screws from the cover.
• Loosen the cap nut for the cable gland.
• Remove the clamp on the cable grip by unscrewing the two screws.
• Remove the insulation on the mains cable to the required length.
• First, thread the power cable through the cap nut and then through the cable gland.
• Connect the power cable to the terminal strip in the LED spotlight:
Brown wire = L (phase)
Blue wire = N (neutral wire)
Green-yellow wire = PE / protective earth wire/ earthing symbol
The protective earth wire must be connected!
Do not install the LED spotlight, if the LED spotlight is replacing an existing light and
there is no protective earth cable available. First, draw a new mains cable.
Where the protective earth is not connected, a fault with the mains voltage might
result in the metal housing of the LED spotlight becoming live. There is a risk of a
life-threatening electric shock!
Make sure only the minimum required length of the cable is stripped; otherwise it could cause
a short-circuit.
Also check the other screw connections on the terminal strip (for the connection cables to the
light electronics) and tighten them if necessary.
• Fasten the mains cable in the cable grip. Attach the cable grip's clamp, removed previously,
and screw it fi rmly in place.
• Screw the cable gland's cap nut tight so the rubber seal inside the cable gland is sealed.
• Attach the cover previously removed and screw it fi rmly in place with four screws.
• Adjust the LED spotlight's angle so it illuminates the desired area.
• Switch on the mains voltage again and make sure that the light is working.
If the LEDs in the LED spotlight do not light up, switch off the power immediately and
have the connection of the light checked by a qualifi ed technician (e.g. electrician)!
Maintenance and Care
• The LED spotlight is maintenance-free, this is why you should never open or dismantle it
(apart from the connection / installation described in this operating manual).
• You should occasionally clean dust and dirt off the glass plate on the light to ensure proper
functioning.
• Before cleaning, switch off the LED spotlight or disconnect it from the mains voltage. Let it
cool down suffi ciently.
• The exterior of the LED spotlight should only be wiped with a clean, soft, dry cloth. Where it
becomes very dirty, use a cloth which is slightly moistened with lukewarm water.
Do not use aggressive cleaning agents or chemical solutions that could damage the housing
(discolouring) or impair operation.
Do not press too hard on the housing or the glass plate, as scratches might appear.
Never spray water e.g. with a garden hose or a high-pressure cleaner, at the LED
spotlight!
Disposal
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
Technical Data
Operating voltage .........................220 - 240 V/AC, 50 Hz
Power ..........................................Max. approx. 9 W
Protection class ............................I
Protection type ..............................IP54
Installation location .......................Indoors and outdoors
Light source ..................................6 LEDs of 1W each, not replaceable
Light colour ...................................6400 K
Luminous fl ux ...............................450 lm
Ambient temperature ....................-20 °C to +60 °C
Weight ..........................................approx. 0.58 kg
Dimensions (W x H x D) ...............145 x 130 x 95 mm (without mounting bracket)
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.
Werbung
Inhaltsverzeichnis
