Installation; Operation - Conrad 56 05 04 Bedienungsanleitung

Controls
1
2 3
5
4
7
8
6
1 Thermostat Controller
2 Switch for heating circuit 1 ("O" = Off, "I" = On)
3 Switch for heating circuit 2 ("O" = Off, "I" = On)
4 Adjustment wheel for time adjustment of the timer; with 96 sliding switches to switch the
radiant heater on/off; only turn right, in clockwise direction!
5 Sliding switch for timer ("I" = continuous operation, "
6 Caster bracket
7 Cap nut
8 Caster
9 U-shaped retaining bracket

Installation

• For the installation, place the oil-fi lled radiant heater on a soft surface so that the housing
cannot get scratched.
☞
The gills are not 100% fi lled with oil. Thus, when turning the heater, you will hear
gurgling sounds of the oil inside the gills. This is normal.
• Attach the two caster supports (6) to the underside of the radiant heater by using the U-
shaped retaining brackets (9).
☞
Make sure you fasten the caster supports at the left and right end of the heater so
that it cannot tip over that easily. See illustration above.
Hang the hook of the U-shaped bracket into one of the holes of the caster support. Put the
other end of the bracket (the one with the thread) through the other hole of the caster support.
Attach the butterfl y screw to the thread and rotate it and thus, fasten the caster support and
the bracket on the radiant heater.
• Afterwards, the 4 casters (8) must be mounted on the two caster supports by using one cap
nut (7) for each caster.
• Turn the oil-fi lled radiant heater around so that it is standing on the casters.

Operation

• Switch the two heating circuits (2) and (3) off (switch position "0").
• Turn the thermostat control (1) to the "0" position .
• Move the sliding switch of the timer to the position "I" (timer deactivated)
• Plug the mains plug into a earthing contact socket.
• The two switches (2) and (3) are used to select the required heating output. Observe the
labels next to the switches. You can select the heating output in a total of 3 levels (off, low,
medium, high).
• With the thermostat control (1) you can set the temperature at which the radiant heater will
be switched off. An arrow marking in the housing next to the thermostat control indicates the
current adjustment level (0.....7).
If the temperature drops by several degrees, the heater will be switched on again automati-
cally.
☞
The control lights in the switches (2) or (3) light up if the heating circuits of the radiant
heater are activated.
9
" = timer activated)
Using the timer
• If you wish to use the timer, move the sliding switch (5) of the timer to the position "
activated).
Using the timer can help you save energy since the oil-fi lled radiant heater will only work
when you really need it. First set the desired temperature via the thermostat control (1)
and depending on your heat requirement, activate the heating circuits 1 and 2 using the two
switches (2) and (3).
• Turn the adjustment wheel (4) to the current time. An arrow points at the corresponding time.
☞
Only turn the adjustment wheel to the right, in clockwise direction!
• With the small sliding switches at the outer edge of the adjustment wheel (4) you can now
choose when the radiant heater will be switched on (4 sliding switches per hour).
☞
If the small sliding switches are moved outwards in direction of the edge, the heater
will be switched on at this time.
If you move the small sliding switches inwards, the heater will be switched off at this
time.
• To deactivate the timer, move the sliding switch (5) to the "I" position. Now the oil-fi lled radi-
ant heater can only be controlled via the adjustment of the thermostat control (1).
Maintenance and Cleaning
• Only a professional repair shop should attempt to maintain or repair the device. The product
contains no parts that require servicing. Therefore, do not open/dismantle it.
• The heater must be switched off before cleaning. Furthermore, disconnect the mains plug
from the mains socket. Then allow the heater to cool down completely.
• To clean the outside of the product, a dry, soft and clean cloth is suffi cient.
• Dust can easily be removed using a clean, soft and long-haired brush and a vacuum cleaner.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions, since
these could damage the housing or even impair operation.
Disposal
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
Technical Data
☞
Variations in dimensions and weight are dependent on the production technique.
Item no. 560503, (9 gills):
Operating voltage .........................230 V/AC, 50 Hz
Heating output: .............................800 W + 1200 W (in total 2000 W)
Dimensions (H x L x W) ................650 x 420 x 240 mm
Weight ..........................................approx. 11.8 kg
Item no. 560504, (11 gills):
Operating voltage .........................230 V/AC, 50 Hz
Heating output: .............................800 W + 1200 W (in total 2000 W)
Dimensions (H x L x W) ................650 x 490 x 240 mm
Weight ..........................................approx. 14.1 kg
Item no. 560506, (13 gills):
Operating voltage .........................230 V/AC, 50 Hz
Heating output: .............................1000 W + 1500 W (in total 2500 W)
Dimensions (H x L x W) ................650 x 570 x 240 mm
Weight ..........................................approx. 16.5 kg
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.
" (timer