Installation; Operation - Conrad 55 43 43 Bedienungsanleitung

Installation

Never operate the product without the wheels (4). First install the wheels before
using the product.
1. Fasten two wheels (4) on each wheel holder (3).
2. To do so, first insert one of the four long screws from below into the suitable opening in the
wheel (4).
3. Place one of the four small washers on the screw.
4. Place one of the four small split washers on the screw.
5. Using a Phillips screwdriver, fasten the wheel (4) to the outer corner of the wheel holder (3).
6. Repeat these steps to install the rest of the wheels (4) to the wheel holders (3).
7. Fasten both wheel holders (3) to the thermal wave heater.
8. To do so, first place one of the two large split washers on the short screw.
9. Place one of the two large washers on the short screw.
10. Using a Phillips screwdriver, fasten the wheel holder (3) to the bottom of the thermal wave
heater. The round side of the wheel holder should face outward.
11. Repeat these steps to fasten the second wheel holder (3) to the bottom of the thermal
wave heater.
12. The product is now fully assembled and ready for use.

Operation

Unpleasant odors may occur for some time during first use. Make sure the room
where the product is set up is sufficiently ventilated.
Place the product on a sufficiently large, stable, heat-resistant and even surface.
Make sure that the product will not roll off on its own.
1. Make sure that both switches I (6) and II (7) are in position "Off".
2. Make sure that the thermostat knob (8) is turned all the way counter clockwise to position
Low.
3. Connect the power plug to a common household power outlet.
4. Turn the product on using the switches I and/or II. The following heating levels are available:
- Switch I (6) only at position "On"
- Switch II (7) only at position "On"
- Switch I (6) + II (7) at position "On"
5. Turn the thermostat knob (8) all the way clockwise to position High. Once the desired room
temperature is reached, slowly turn the thermostat knob until you hear a clicking sound.
The red indicator lamp (5) control up once the heating function is activated.
Once the desired temperature is reached, the thermostat turns off the heating
function temporarily. The indicator lamp (5) goes out.
As soon as the temperature sinks below a certain value, the thermostat reactivates
the heating function.
6. Press the switch(es) I / II to turn off the device.
7. Unplug the product when it is not in use.
Long screw
Wheel
Small washer
Small split washer
Wheel holder
Short screw
Large split washer
Large washer
Wheel
Wheel holder
Thermal wave heater
Heating function with max. 1200 W
Heating function with max. 800 W
Heating function with max. 2000 W
Overturning and overheating protection
• The product has an overturning protection mechanism that automatically deactivates the
heating function should the product tip. When the product is upright again, the heater is
reactivated. Make sure the product cannot accidentally tip over.
• The product also has a thermal fuse without automatic reset that is triggered if, for instance,
the heat guard (1) is blocked. In this case, the product cannot be operated.
Maintenance and cleaning
Never use any aggressive cleaning agents or chemical solutions as these may cause
damage to the housing or impair the product's functioning.
Do not apply too much pressure to the surfaces as this could cause scratching or
dents.
• Besides occasional cleaning, the device is maintenance-free.
• Before cleaning, turn off and unplug the product. Allow it to cool down completely.
• To clean the housing, use a dry, soft and clean cloth.
• Remove dust from the heat guard (1) with a long-haired, soft and clean brush or vacuum
cleaner.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage .......................... 220 – 240 V/AC, 50 Hz
Power consumption . ...................... max. 2000 W
Power level Switch I ...................... 1200 W
Power level Switch II ..................... 800 W
Power level Switch I + II ................ 2000 W
Suited for spaces up to . ................. 20 m
Cable length .................................. 1.5 m
Dimensions (W x H x D) ................ approx. 790 x 595 x 295 mm
Weight ........................................... 4.6 kg
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
2
V1_0713_02-ETS-Mkde