Werbung
6.12
SPECIFIC INSTRUCTIONS FOR THE
USE OF MODEL AC 230V
The AC 230V model machine may be turned on
only if the voltage indicated on the tag corresponds
with the available voltage and that the electrical
outlet is grounded (earthed).
Do not damage the feed cable; do not crush or
pull on it.
Do not run over the feed cable with the machine.
The cable could wind up in moving parts causing
a short circuit.
• ATTENTION !!! - The model AC 230V ma-
chine has parts, which are connected to
the current; contact with these could cause
grave injuries or even death.
- Before executing any type of operation on the
machine always disconnect it from the electrical
source.
- Never touch electric cables that are defective or
worn.
- Before gaining access to the electrical system it is
always necessary to disconnect the machine from
the electrical source.
- In the case of defective, damaged, or cracked
electric cables, replace immediately with authentic
replacement parts.
- The network of connections must be protected
from water spray.
- The patch cord for the connection of the machine
to the mains power must conforms to current sa-
fety rules.
- The electrical system to which the machine is
connected must be equipped with a cutout box.
- It is absolutely forbidden to use the machine in
proximity to swimming pools or stretches of water.
• EMERGENCY SITUATIONS
In case of emergency:
- Immediately disconnect the machine from
the power mains.
- Immediately apply proper first-aid.
If an accident should occur the machine must not
be put into operation until a technician authorized
by the manufacturer has examined it.
6.13
DRIVING THE MACHINE
Model AC 230V
- Connect the power cable of the machine ( Photo
B - 1) to the power mains using a patch cord.
- Switch ON the general ON-OFF switch ( Photo
A - 1).
- Switch ON the brush motor switch ( Photo A - 2).
• The brush will start the rotation only when
the machine operator will operate the brush
operation lever ( Photo B - 4).
- Switch ON the suction motor switch ( Photo A
- 3).
- Lower the squeegee unit by using the lift/lower
lever ( Photo B - 3)
- Lower the brush plate unit by using the lift/lower
lever ( Photo B - 2)
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo B - 4); releasing the
lever the brush rotation will stop after few seconds.
• Remember to lift the squeegee before driving
reverse to avoid damaging it.
Model DC 24V
- Verify that the battery connector placed in the
back of the machine ( Photo D - 7) is connected.
- Put the ignition key ( Photo D - 1) in and turn ON
the machine.
- In the control panel, check the battery charge
status ( Photo C - 3 )
- Switch ON the brush motor switch ( Photo C - 1).
( ! ) The brush will start the rotation only when the
machine operator will operate the brush operation
lever ( Photo D - 2).
- Switch ON the suction motor switch ( Photo C
- 2).
- Lower the squeegee unit by using the lift/lower
lever ( Photo D - 4)
- Lower the brush plate unit by using the lift/lower
lever ( Photo D - 3)
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo D - 2); releasing the
lever the brush rotation will stop after few seconds.
• Remember to lift the squeegee before driving
reverse to avoid damaging it.
Model DC 24V with traction
- Verify that the battery connector placed in the
back of the machine ( Photo F - 8) is connected.
- Put the ignition key ( Photo F - 1) in and turn ON
the machine.
- In the control panel, check the battery charge
status ( Photo E - 1 ) and, if sufficient, select the
running speed wished ( Photo E - 3, E - 4 ).
- Switch ON the brush motor switch ( Photo E - 5).
• The brush will start the rotation only when
the machine operator will operate the brush
operation lever ( Photo F - 2).
- Switch ON the suction motor switch ( Photo E
- 6).
- Lower the squeegee unit by using the lift/lower
lever ( Photo F - 4)
- Lower the brush plate unit by using the lift/lower
lever ( Photo F - 3)
- Wash the floor moving forward by pulling the
traction lever ( Photo F - 2) up or push the traction
lever down to reverse traction; releasing the lever
the traction will stop immediately and brush rota-
tion will stop after few seconds.
• Remember to lift the squeegee before driving
reverse to avoid damaging it.
36
Werbung
Kapitel
