Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Car seat cover set
Introduction
We congratulate you on your purchase. You have chosen a high
quality product. The instructions for use are to be considered as
part of this product. Before using the product, please familiarise
yourself with all the safety information and instructions for use. Only use the
product as instructed and only for the stated areas of use. If you pass the product
on to anyone else, please ensure that you also pass on all the documentation
with it.
Intended use
Car seat covers for the driver's seat and passenger's seat of cars (according
to the enclosed type list).
Scope of delivery
1 x cover for front seat
Safety instructions
Correct installation res. fastening of the seat covers to the vehicle is essential
to guarantee the safety of the user. Please pay attention to the following
information when installing the seat covers:
WARNING!
the packaging out of reach of small children.
Installation is permissible only in cars that are indicated in the list of types
on the packaging or in the enclosed, detailed list of types.
Headrest inserts, adjustment levers / wheels for release of backrests or
armrests may not be covered with the seat cover. Allowances must be
made for appropriate inserts. Please observe the instructions given in
section "Installation".
Displaced seat covers must be repositioned. If this is no longer possible
due to a advanced state of wear and tear, the cover must be removed or
replaced.
Manipulation of the opening of the seat covers is not permissible
(no covering, sewing up or repairs by yourself).
This protective cover has been tested by TÜV Rhineland Group.
CAUTION! If the seat covers are installed incorrectly, the proper extension
and inflation of the seat air bag cannot be guaranteed in the case of a
collision.
List of types
+ Assembly and safety advice
DANGER OF SUFFOCATION! Keep
Installation
You need a pair of pointed scissors.
Installation of seat covers
Important: Please read the information below before installing the seat covers!
Fig. 1:
Remove headrests (in some car models the headrests must
be dismantled in a garage).
Fig. 2:
Cover the backrest by pulling the cover downwards.
Fig. 3:
Pull the strap through between the seat and the backrest.
Fig. 4:
Then close the fastener.
Fig. 5:
Cover the seat from the front to the back.
Fig. 6:
Pull the rear rubber loops between the seat and backrest
(as you did with the strap of the backrest cover). Fasten the
metal hooks under the seat according to the car model
(e.g. to the existing metal rods - ATTENTION Do not fasten
to airbag cables!)
Fig. 7:
Or fasten all rubber loops together.
ATTENTION!
Openings for backrest releases, adjustment levers, side levers etc. (as described
under fig. 11–21) must be cut out.
If your seat is equipped with armrests, proceed as described
under fig. 8. Otherwise go to fig. 11.
Fig. 8:
Pull the cover down as far as the armrest. The cover must be
tightly fitting on top.
Fig 9:
Cut the cover in the position of the armrest. The cut-out may
not be too large. Push up the armrest and pull it through the
cut-out opening of the cover.
Fig. 10:
Pull the strap through between the seat and the backrest and
close with the fastener.
If your seat is equipped with side levers, proceed as described
under fig. 11. Otherwise go to fig. 13.
Fig. 11:
Cover the seat as described under section 2. The cover must
be tightly fitting on top.
Fig. 12:
Cut the cover in the position of the side lever. The cut-out may
not be too large.
Fig. 13:
With the aid of scissors, push the cover under the guide fitting.
If your seat is equipped with seat frame cladding, proceed as
described under fig. 14. Otherwise go to fig. 14.
Fig. 14:
(for Renault) Open the seat frame cladding under the seat.
Fig. 15:
(for Mercedes) Open the seat frame cladding under the seat.
Fig. 16:
Fold the seat frame cladding under the seat cover. Pull the
strap through between the seat and the backrest. Then close
the fastener at the back.
Fig. 17:
Position the mounting strip directly above the holes for insertion
of the headrest. Cut open the mounting strip in the exact
positions of the headrest holes. With the aid of the integrated
mounting strip, it is not possible for the material to tear.
Fig. 18+19: Push the cover beneath the plastic of the headrest guide
covering. In a few isolated car models, it could be the case
that these models have no headrest guide covering.
GB 7
Werbung
