Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OBJ_BUCH-2019-004.book Page 20 Thursday, March 24, 2016 8:41 AM
20 | English
Apply the power tool to the workpiece only when switched on.
Move the machine with a circular motion or alternately in
length and crosswise direction over the workpiece/surface
applying moderate pressure. For removal of coatings, the ma-
chine can also be guided at a small angle to the workpiece sur-
face without a reduction of the dust extraction capacity.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
A blunt diamond cup wheel 15 can be reground by briefly
grinding abrasive material (e.g. lime-sand brick).
Please store and handle the accessory(-ies) carefully.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Changing the Brush Collar
To ensure optimal dust extraction, change a worn brush collar
in good time.
GBR 15 CA: Using a screwdriver, carefully pry out the brush
collar 11 at the openings of the brush guide with the diamond
cup wheel 15 mounted. Use the diamond cup wheel for lever-
age while prying out.
Carefully push a new brush collar 11 to the stop into the brush
guide. When inserting the new brush collar, pay attention that
the ends of the brush collar are not positioned in one of the
openings of the brush guide.
GBR 15 CAG (see figure C): Press (for example with a screw-
driver) into both openings 5 of the guard. You can remove
both parts of the brush collar 4 from under the machine.
Carefully push the two new parts of the brush collar 4 to the
stop into the brush guide. When inserting the new brush col-
lar, pay attention that the ends of the brush collar are not po-
sitioned in one of the openings of the brush guide.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
1 609 92A 2AS | (24.3.16)
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: bsc@zsd.co.za
Bosch Power Tools
Werbung
Inhaltsverzeichnis
