Inhaltsverzeichnis
Werbung
OBJ_BUCH-1797-003.book Page 19 Thursday, September 19, 2013 2:38 PM
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are: Sound pressure level 92 dB(A); Sound power level 103 dB(A). Uncer-
tainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K determined accord-
h
ing to EN 60745:
Surface grinding:
a
h
K
Disk sanding:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker
Helmut Heinzelmann
Executive Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
20.09.2013
Bosch Power Tools
3 601 ...
2
m/s
2
m/s
2
m/s
2
m/s
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance for addresses, see section "After-
sales Service and Application Service".
Protection Guard for Grinding
Place the protection guard 5 on the spindle collar. Adjust the
position of the protection guard 5 to the requirements of the
operation and lock the protection guard 5 with the locking
screw 6.
Adjust the protection guard 5 in such a manner that
sparking is prevented in the direction of the operator.
Protection Guard for Cutting
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 13.
Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 13 is mounted in the same
manner as the protection guard for grinding 5.
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard 24 is
mounted in the same manner as the protection guard for
grinding 5.
Auxiliary Handle
Operate your machine only with the auxiliary handle 3.
Screw the auxiliary handle 3 on the right or left of the machine
head depending on the working method.
Hand Guard
For operations with the rubber sanding plate 20 or with
the cup brush/wheel brush/flap disc, always mount the
hand guard 18.
The hand guard 18 is fastened with the auxiliary handle 3.
English | 19
H49 L..
H51 L..
H50 L..
H52 L..
9.5
9.5
1.5
1.5
5.5
4.0
1.5
1.5
1 619 P11 591 | (19.9.13)
Werbung
Inhaltsverzeichnis
