Disassembly Of Glass Pane In Door; Supplementary Installation Instructions Per Appliance - Dik Geurts Instyle 500 EA Installationsanleitung

9.4 Glass pane
-
!Caution
-
Use the supplied pane window cleaner to remove fingerprints/dirt on the glass pane.
Tip!

9.4.1 Disassembly of glass pane in door

To remove the glass pane in the door follow the instructions below:
Ø
Open the door.
Ø
Lift the door out by first sliding it upwards, then tilt it slightly forwards and allow it to lower.
Ø
Place the door on a flat surface.
Ø
Remove the nuts from the strips.
Ø
Remove the strips.
Ø
Lift the glass pane out. The pane seal is then also taken out.
-
Tip!
-
9.4.2 Assembly of glass pane in door
Assemble the glass pane in the door according to the steps described in paragraph 9.4.1 '9.4.1 Disassembly of
glass pane in door' but in reverse order.
Assembly of the door is somewhat different.
!Caution
Proceed as for assembly of the door:
Ø
Bring the hole at the bottom of the hinging part of the door exactly below the lower pin.
Ø
Slide the door up. The pin slides into the lower hole.
Ø
Bring the hole at the top of the hinging part of the door exactly above the upper pin and allow the door to lower.
The pin slides into the upper hole.
Ø
The door is now assembled.
-
!Caution
-
9.5 Frames
The appliances can be fitted with various frames. The frames are adjustable in depth and can be fitted so they are
parallel to the door.
The installation depth of the appliance depends on the selected frame (see Annex 2, fig. 1)!
!Caution
When assembling the frame proceed as follows:
First remove the door before assembling the frame.
Tip!
In-built frame (no frame):
Ø
Remove the 4 pre-assembled bolts/nuts (see Appendix 2, Fig. 12).
Ø
Slide the frame over the stove into the desired position (see Appendix 2, Fig. 13).
Ø
Fasten the 4 bolts and nuts (the bolts on the inside, the nuts on the outside of the appliance)
(see Appendix 2, Fig. 14).
Ø
Fasten the 2 bolts and nuts on top of the appliance (see Appendix 2, Fig. 14).
Other frames:
Ø
Loosen the 4 pre-assembled bolts (see Appendix 2, Fig. 15).
Ø
Slide the frame in the convection casing between the loosened bolts and the bolts still tight in the appliance
(see Appendix 2, Fig. 16).
Ø
Tighten the nuts. The frame is now clamped between the nuts (see Appendix 2, Fig. 17).

9.6 Supplementary installation instructions per appliance

The two front adjustable feet of the Instyle and Prostyle 500
On these adjustable feet there is a hexagonal nut that is adjusted from outside with an open-end spanner. The
rear adjustable feet are accessible after the removal of the vermiculite plates lying on the bottom.
Adjust the front feet before assembling the frame.
Tip!
UK
Avoid damage when removing/fitting the glass pane;
Avoid/remove fingerprints on the glass pane because these burn in.
When replacing the glass pane always replace the seal in the door (= seal between the glass pane and the
door).
Check the door sealing cord and replace if necessary (see paragraph 9.3).
Do not fasten the bolts too tight to avoid breaking off and/or stripping: overtightening will cause breakage.
Place the glass pane (including new pane seal) with the logo to the bottom right.
EA EA
and 550 models are not adjustable from inside.
IN S TA L L A TI O N M A N U A L