Built-In Fires - Dik Geurts Instyle 500 EA Installationsanleitung

Installing with build-in cassette (if applicable):
Ø
Place the fire with build-in cassette on a floor with a sufficient load bearing capacity.
Ø
Install the build-in cassette for a fire-safe wall.
Ø
If there is a flammable wall build a 10 cm-thick fire-safe wall.
Ø
Place the build-in cassette level at the desired height and fix it with metal anchors.
Ø
With a corner model fix the tie rod to the wall and adjust it.
Ø
Connect the flue duct to the cassette ring.
Ø
The cassette is not suitable for supporting a flue duct; this must be self-supporting.
Ø
Use non-combustible and heat-resistant material according to European fire classification A1 EN 13501-1 for the
chimney breast (including the upper face), the material in the chimney breast and the back wall against which the
appliance is fitted. Plate material or stony materials can be used for this.
Ø
If the chimney breast is made of heat-resistant plates according to European fire classification A1 EN 13501-1 such
as Promafour, Promatect, Nobranda etc., it can be fixed to the cassette.
Ø
Stony materials may not rest on the cassette; for this use a brick lintel with ceramic felt.
Ø
Leave a space of 6 mm between the cassette and the chimney breast walls.
Ø
Cover the cassette with 6 cm of heat-resistant insulation material.
Ø
Take account of the expansion of the cassette. Keep the cassette free of plasterwork.
Ø
The chimney breast may not be warmer than 90 degrees Celsius on the outside.
Ø
If there is a flammable ceiling, place a fire-resistant plate with a 10 cm thick heat-insulating layer on top 30 cm
below the ceiling in the chimney breast.
Ø
Place the fire before the build-in cassette.
Ø
Turn in the adjustable legs and check whether they are properly adjustable. There may still be some blasting grit
present.
Ø
Carefully slide the fire into the hole. Make sure that no damage is caused.
Ø
Turn the adjustable legs with the associated Allen key so the fire comes into the desired position. Make sure that
sufficient space remains under the fire for the supply of combustion air.
Ø
Make a good, airtight seal between the fire and the flue.
Ø
Leave a space of at least 10 mm between the fire and cassette.
Ø
If applicable fit the restrictor cap for the outflow, place the vermiculite plates in reverse order and place the baffle
plate against the back wall and on the profiles.
Ø
Fit the frame if it is supplied separately.
Ø
Lay a fire-resistant floor plate for the fire if the floor is flammable. The floor plate in non-flammable material must
extend at least 300 mm away from the fire and be at least 300 mm wider than the fire.

5.4.3 Built-in fires

Ø
Determine the place of the fire.
Ø
Slide the build-in frame into the desired position.
Ø
Use non-combustible and heat-resistant material according to European fire classification A1 EN 13501-1 for the
plate on the floor, chimney breast (including the upper face), the material in the chimney breast and the back wall
against which the appliance is fitted. Plate material or stony materials can be used for this.
Ø
If there is a flammable ceiling, place a fire-resistant plate with a 10 cm thick heat-insulating layer on top 30 cm
below the ceiling in the chimney breast.
Ø
Place the fire level at the desired height and fix it with metal anchors.
Ø
Connect the flue duct to the fire ring.
Ø
Always connect any convection openings with heat-resistant flexible pipe and ventilation elements to protect the
plasterwork against high temperatures. If the chimney breast is made of non-combustible materials (e.g. facing
brickwork) this is not required.
Ø
Make sure there is sufficient space under the fire for the supply of combustion air. When the outside air
connection ring is not used, it must remain at least 20 mm free for sufficient combustion air.
Ø
If applicable connect the outside air connection (see section 9 'Appliance-specific information').
Ø
The fire is not suitable to support a flue duct, it must be self-supporting.
Ø
Stony materials may absolutely not rest on the fire. For this use e.g. a brick lintel with ceramic felt.
Ø
Make sure that the opening in the chimney breast is 6 mm wider than the built-in frame.
Ø
The chimney breast may not be warmer than 90 degrees Celsius on the outside;
Ø
Lay a fire-resistant floor plate for the fire if the floor is flammable. The floor plate in non-flammable material must
extend at least 300 mm away from the fire and be at least 300 mm wider than the fire.
UK
IN S TA L L A TI O N M A N U A L