Renkforce RRF1 6x32 Bedienungsanleitung Seite 6

k) Speed measurement
Speed measurement will allow you to measure the time needed for a moving object to get from
one point to another. The product automatically calculates the speed by means of the covered
distance and time.
The product can only measure the speed of objects that move directly towards or away from you.
It cannot measure the speed of objects that move from left to right (or right to left) within your
field of view.
• Press the M button, until the following appears:
X1
1005hPa 29°C
• Briefly press the on/off button to start measuring. The target point display starts flashing.
• Target a moving object for a few seconds. Shortly after that, the display will show the measured speed.
Settings
• Press and hold the M button, until the "setup" indicator appears below the target point display.
• Press the on/off button to adjust the unit or value.
• Press the M button to switch to the next parameter. The following parameters are available for selection:
Parameter
1. OSD color (display color)
2. Temperature
3. Distance
4. Height
5. Speed
6. Power OFF (automatic switch-off if no activity)
• Press and hold the M button for approx. 2 seconds to exit the settings menu.
If you do not press any button for 30 seconds, the product will automatically switch to normal
viewing mode.
Button illumination
In order not to attract any unwanted attention during darkness, the buttons are not illuminated. It
is possible, though, to briefly activate button illumination for easier operation. Proceed as follows
to do so:
• Tilt the product downwards by at least 45°.
• Press any button. All buttons will be illuminated for a max. of 15 seconds.
• If the tilting angle is less than 45°, the illumination of the buttons will deactivate even before the 15 seconds
have elapsed.
Hand strap
• Guide the long strap with the soft side facing up through the two eyelets (5).
• Flip over the hand padding in order for the side with the synthetic leather to face to the outside.
• Open the hook-and-loop fastener of the hand padding.
• Insert the long strap into the hand padding and then close the hook-and-loop fastener.
Tripod socket
• There is a tripod thread located on the bottom of the product.
• If needed, mount the product to a suitable tripod with a socket diameter of 6.35 mm (1/4").
Tips and notes
• Light refraction and sunlight can cause measuring errors during outdoor use.
• Smog, dust, rain, and snow can reflect the laser beam, resulting in measuring errors.
• When using the product outdoors, protect it from moisture and humidity.
• The following surfaces can affect the measurement due to their physical characteristics:
- Transparent surfaces (e.g. glass, water)
- Reflecting surfaces (e.g. glass, shiny metals)
- Porous surfaces (e.g. insulating materials)
- Structured surfaces (e.g. roughcast, natural stone)
+05°
– – – – km/h
SE132° IR:OFF
Unit / value
1. Yellow
2. Green
3. Red
4. Blue
5. White
6. Black
°C (Celsius), °F (Fahrenheit)
M (meter), Yd (yard)
M (meter), Ft (feet)
km/h (kilometers per hour)
Mile/h (miles per hour)
5 min, 10 min, 15 min, 20 min, 25 min, 30 min,
35 min, 40 min
Cleaning and care
• Under no circumstances use aggressive cleanings agents, cleaning alcohol or other chemical solutions
since these can penetrate the housing or impair functionality.
• Do not submerge the product in water to clean it.
• Do not apply too much pressure to the lens to prevent scratching.
• The product is maintenance-free except for potential battery replacement and occasional cleaning.
• Use the provided cleaning cloth or a dust brush for cleaning the lenses. You can also use a soft, lint-free
cloth. A glasses cloth can also be used to clean the lenses. If necessary, you can moisten the cloth with
a little lukewarm water.
• If cleaning the lenses with a cleaning cloth, make sure the cleaning agent does not drop directly onto the
lenses. Always apply the cleaning agent directly to the cloth first.
• Clean the housing with a dry, clean, soft and lint-free cloth. To remove tougher stains, slightly dampen the
cloth with lukewarm water.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
Remove any inserted (rechargeable) batteries and dispose of them separately from the product.
b) (Rechargeable) batteries
You as the end user are required by law (Battery Ordinance) to return all used (rechargeable)
batteries. Disposing of them in the household waste is prohibited.
Contaminated (rechargeable) batteries are labeled with this symbol to indicate that disposal
in the domestic waste is forbidden. The designations for the heavy metals involved are: Cd =
Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash icon
on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our stores or wherever
(rechargeable) batteries are sold.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
Power supply ........................................ 4 x AA battery (not included)
Measuring range ................................... 4 - 500 m (distance)
300 - 1100 hPa (atmospheric pressure)
±20° (inclination angle)
Night vision distance ............................. max. 200 m
Zoom .................................................... 6x optical, 4x digital
Lens Ø .................................................. 32 mm
Angle of view ........................................ 6°
Field of view (m/1000 m) ...................... 105 m
Diopter adjustment ............................... ±4
Display resolution ................................. 480 x 240 pixels
Compass resolution .............................. 1°
Laser class ........................................... I
Wavelength ........................................... 850 nm
Prism .................................................... Porro prism
Lens coating ......................................... full multi-coating
Operating conditions ............................. +10 to +50 °C, 0 - 90 % RH
Storage conditions ................................ +10 to +50 °C, 50 - 70 % RH
Dimensions (L x W x H) ........................ 175 x 100 x 51 mm
Weight .................................................. 426 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE. *1486094_V1_0916_02_IPL_m_en