Bosch PST 800 PEL Originalbetriebsanleitung Seite 14

OBJ_BUCH-1065-003.book Page 14 Wednesday, October 5, 2011 10:35 AM
14 | English
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a =13 m/s , K=3 m/s
h
2
Cutting sheet metal: a =7 m/s , K=1.5 m/s
h
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Engineering Director
Engineering PT/ESI
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 05.10.2011
Assembly
Before any work on the machine itself, pull the mains
plug.
Replacing/Inserting the Saw Blade
When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of these instructions. Use only T-shank saw blades or saw
2 609 005 649 | (5.10.11)
blades with 1/4" universal shank (U-shank). The saw blade
should not be longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A1)
Clean the shank of the saw blade before inserting it. An
unclean shank cannot be fastened securely.
If required, remove the dust cover 9 (see "Dust Cover").
Push the saw blade holder 13 upward in the direction of the
2
,
arrow. Insert the saw blade 15 (teeth in cutting direction) to
2
.
the stop into the saw blade holder.
While inserting the saw blade, pay attention that the back of the
saw blade is positioned in the groove of the guide roller 14.
Check the tight seating of the saw blade. A loose saw
blade can fall out and lead to injuries.
Removing the Saw Blade (see figure A2)
Push the saw blade holder 13 upward in the direction of the
arrow and remove the saw blade 15.
If the saw blade is wedged or jammed when removing, set ad-
justing lever 7 to maximum orbital action and press the saw
blade holder 13 lightly toward the front (max. 2 mm).
Saw Blade Storage (see figure B)
Up to six saw blades with lengths to 110 mm can be stored in
the saw blade storage 5. Insert the saw blades with the T-shank
into the recess of the saw blade storage intended for this. Up to
three saw blades can be placed on top of each other.
Shut the saw blade storage and slide it to the stop into the
opening of the base plate 6.
Splinter Guard (see figure C)
The splinter guard 16 (accessory) can prevent fraying of the
surface while sawing wood. The splinter guard can only be
used for certain saw blade types and only for cutting angles of
0°. When sawing with the splinter guard, the base plate 6
must not be moved back for cuts that are close to the edge.
Press the splinter guard 16 from the bottom into the base
plate 6.
"Cut Control"
"Cut Control" enables precise guiding of the power tool along
a cutting line marked on the workpiece. The "Cut Control" kit
includes the viewing window 11 with cutting marks and the
base 10 for attachment to the power tool.
Attaching "Cut Control" to the Base Plate (see figure D)
Clamp the "Cut Control viewing window " 11 into the holders of
Cut Control base 10. Then, lightly press the base together and
allow it to engage into the accessory holder 17 of the base plate.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
Bosch Power Tools