Jamara 50 0175 Bedienungsanleitung Seite 8

GB - Getting Started
Make sure that all parts from the box content are included. Trans-
mitter, Car, Charger, battery pack.
Ladegerät
Akku
Ladeadapter
The battery pack has to be charged before use. Plug the charger
into a 230V outlet. Connect the charger to the battery. If the plug
of the charger and battery do not match, then you will find a con-
nection lead in your box. The average charging time of the empty
battery is about 6-8 hours.
Place 8 pieces of AA batteries into the
transmitter. If rechargebale, please also
make sure these are fully charged.
Read the chapter for usage of the
transmitter and its controls carefully.
Turn the radio off and make sure all the
trim buttons on the transmitter are in
neutral position.
You have purchased a RTR model, which
L/R F/B
means it should be ready for immedia-
te use after charging all batteries. You
Trim
need to check the car, electronics and
On/Off
all plastic parts after each use to make
sure no parts are damaged. Also all the
moving parts must be checked for their
clearance, bolts and screws that they are tight.
Now put the battery into the
battery holder in the vehicle.
Make sure that the battery
holder is secured properly
with the 2 included clips for
the battery holder. Now con-
nect the battery to the speed
control in the model.
Keep the car in the air in case
that the motor turns at full
power.
Switch the speed control on the On / Off switch. Set the model on
the ground and test it for proper functioning. Steering right/ left,
throttle/ brake, forward and backward. If the wheels do not point
straight forward even though the steering wheel on the transmitter
is in neutral, you can adjust it with the trim button on the trans-
mitter.
Trim L/R = steering
Trim V/R = forward/backward
Should the wheels rotate forward or backward, even though no
command was given through the transmitter, then also the throttle
needs to be trimmed on the transmitter.
We encourage you now to activate your receiver's built-in Failsafe
unit. On delivery it is turned off.
8
Akku
Netzteil
Balancer
Battery
ESC/Battery
Connector
On/Off
ESC
Leave the throttle lever in neutral position (see chapter Fail Safe). Press
the fail-safe button on the receiver until it flashes and let go to activate.
Check this principle in an electric vehicle only in the neutral
position of the throttle, because otherwise the model goes
into the previously programmed throttle position in a loss of
the transmitter signal.
Now you can make the first test drive. If this is your first rc car, we
recommend to drive it on a small test track to familiarise yourself
with the control of the vehicle and the controls of the transmitter.
Attention!
Your vehicle has a pivot front suspension. This has a number of
advantages. It is very robust and easy to maintain. The set-up of the
car has been done so the drive shaft will not pop out. As with any
model, screws and bolts can losen during break-in of the car. This
can result in tolerance of the drive shaft. The drive shaft can then
pop out if high pressure is applied.
The inner ball screw (item No.: 505081) will enable you to adjust
the tolerance resulting in fine adjustments of the track width. For
best results when setting up the pivot ball for the first time, please
always adjust the upper and lower pivot in the same way. Fasten
as far as the pivot can still be pulled up and down easyly but not
as far that it will pop out if you give full steering angle. The outer
plastic socket screw (item No.: 505080) is only used for securing of
the steering knuckle. This should not be too tight, otherwise the
steering is not smooth and the handling can be adversely affected.
50 5080
Important!
By using LiPo batteries take care that the undervoltage shutdown
is activated, see page 20 - 23
Otherwise, your LiPo battery can be damaged by deep discharge.
We recommend a cut-off voltage of 3 V per cell
50 5081
07 9996
50 5079