Adjusting Setup Items - Set - Sony MEX-BT4700U Bedienungsanleitung

Customizing the equalizer curve
— EQ3
"CUSTOM" of EQ3 allows you to make your
own equalizer settings.
1
Select a source, then press the select
button repeatedly to select "EQ3."
2
Rotate the control dial to select
"CUSTOM."
3
Press the select button repeatedly
until "LOW," "MID" or "HI" appears.
4
Rotate the control dial to adjust the
selected item.
The volume level is adjustable in 1 dB steps,
from –10 dB to +10 dB.
Repeat steps 3 and 4 to adjust the equalizer
curve.
To restore the factory-set equalizer curve,
press and hold the select button before the
setting is complete.
5
Press (BACK).
The setting is complete and the display
returns to normal play/reception mode.
Tip
Other equalizer types are also adjustable.
Adjusting setup items — SET
1
Press and hold the select button.
The setup display appears.
2
Press the select button repeatedly
until the desired item appears.
3
Rotate the control dial to select the
setting (example "ON" or "OFF").
4
Press and hold the select button.
The setup is complete and the display returns
to normal play/reception mode.
Note
Displayed items will differ, depending on the source
and setting.
The following items can be set (follow the page
reference for details):
CLOCK-ADJ (Clock Adjust) (page 7)
CT (Clock Time) (page 13, 14)
BEEP
Activates the beep sound: "ON," "OFF."
AUX-A* 1 (AUX Audio)
Activates the AUX source display: "ON,"
"OFF" (page 24).
AUTO OFF
Shuts off automatically after a desired time
when the unit is turned off: "NO," "30S
(seconds)," "30M (minutes)," "60M (minutes)."
MIC*
1
– "EXT": to automatically switch to the external
microphone when it is connected.
– "INT": to select only the internal microphone.
DEMO (Demonstration)
Activates the demonstration: "ON," "OFF."
DIMMER
Changes the display brightness.
– "AT": to dim the display automatically when
you turn lights on. (Available only when the
illumination control lead is connected.)
– "ON": to dim the display.
– "OFF": deactivate the dimmer.
CONTRAST
Adjusts the contrast of the display. The contrast
level is adjustable in 7 steps.
M.DSPL (Motion Display)
Selects the Motion Display mode.
– "SA": to show moving patterns and spectrum
analyzer.
– "ON": to show moving patterns.
– "OFF": to deactivate the Motion Display.
A.SCRL* 2 (Auto Scroll)
Scrolls long items automatically: "ON," "OFF."
LOCAL (Local Seek Mode)
– "ON": to only tune into stations with stronger
signals.
– "OFF": to tune normal reception.
MONO* 3 (Monaural Mode)
Selects monaural reception mode to improve
poor FM reception: "ON," "OFF."
REG* 3 (Regional) (page 13)
ZAP.TIME* 2 (Zappin Time)
Selects the playback time for the ZAPPIN
function.
– "ZAP.TIME-1 (about 6 seconds),"
"ZAP.TIME-2 (about 9 seconds),"
"ZAP.TIME-3 (about 30 seconds)."
LPF (Low Pass Filter)
Selects the subwoofer cut-off frequency: "OFF,"
"80Hz," "100Hz," "120Hz," "140Hz," "160Hz."
LPF NORM/REV (Low Pass Filter Normal/
Reverse)
Selects the phase when the LPF is on: "NORM,"
"REV."
continue to next page t
23