Nordpeis Quadro Colorado Montageanleitung Seite 10

INDEX
1. General information
Weight
Adjustment
Floor plate
Minor damage
Fine fissures
Painting
2. Before Installing a new fireplace
Chimney Draught
Air Supply
Floor plate
Dimensional drawing
3. Technical Information
4. Safety distances
5. Assembly
Assembly
Fresh air supply set
Operating Control
Removing self-closing door mechanism
6. Lighting the fire for the first time
Lighting a fire
7. Maintenance
Cleaning and inspection
Ashes
Thermotte™ Insulating Plates
Door and glass
8. Warranty
9. Advice on lighting a fire
Some advice in case of combustion problems
Dimensional drawing
Safety distances
1. General information
Weight
The home owner must ensure that the floor can
withstand the load according to the total weight of the
fireplace. When installing the product on a floating wood
floor, the floor boards underneath the fireplace must be
removed, this to avoid the that the floor boards lock and
crack.
Adjustment
We recommend to stack the surround without glue in
order to adjust the insert prior to perforating the chimney
for the flue connection. Use a spirit level to ensure that
the surround is mounted straight. The insert will expand
with heat and for this reason the surround must not rest
on the insert. (Above the insert there must be a gap
of 3 to 5 mm. Laterally there is no need for gaps, but
between the lower part of the insert and the surround
there must be a gap of at least 2 mm.)
10
Floor plate
A fireproof floor plate must be put in front of the fireplace
10
if the floor is of a combustible material.
10
Minor damage
10
The fireplace can sustain minor damage during
10
transport and handling.
10
This can be repaired with acrylic/light filler. For perfect
10
results, you can fill and sand with a suitable filler. Minor
10
damage and uneven surfaces can be filled. If the
10
damage is deep or in the event of significant damage,
you are recommended to fill repeatedly with tile
11
11
adhesive or cement putty to avoid sinking. Smooth off
with e.g. a damp sponge or a float.
11
11
Fine Fissures
11
The building material around the fireplace can move.
12
In new houses in particular, it is common for building
materials to settle substantially in the early years. In
12
addition, all concrete elements shrink to a decreasing
12
extent for up to 15 months.
12
12
The result is that small cracks may appear in the
12
concrete/masonry.
13
13
Use the fireplace for a few months. If cracks appear,
13
scrape them out with a screwdriver or similar (to provide
more space for acrylic joint filler). Vacuum the surfaces
13
to remove any dust.
13
Inject acrylic joint filler and even it out with a spatula or
13
a finger wetted with soapy water.
13
The joint can be painted after a couple of days.
14
14
Painting
When the fireplace has been filled/sanded and the
glued joints are dry, the fireplace is ready to be painted.
16
Use only breathable paint (acrylic) intended for
51
masonry.
53
For your own safety, comply with the assembly instructions. All
safety distances are minimum distances.
Installation of the insert must comply with the rules and
regulations of the country where installed. Nordpeis AS
is not responsible for wrongly assembled inserts.
We accept no liability for typographical errors and changes.
2. Before Installing a new fireplace
All our products are tested according to the latest
European requirements and also to the Norwegian
standard NS 3058 and NS 3059, which include particle
tests. However, several European countries have local
regulations for installation of fireplaces, which change
regularly. It is the responsibility of the client that these
regulations are complied with in the country/region
where the fireplace is installed. Nordpeis AS is not
responsible for incorrect installation.
Important to check
(please note that this list is not exhaustive):
GB