Interconnection Example: Master/Slave-Mode - Hifonics X3-ATLAS Bedienungsanleitung

INTERCONNECTION EXAMPLE: Master/Slave Mode
Remote wire REM
MASTER
Switch position = MASTER
1.
EXTENDED BASS CONTROL
LINE INPUT
L
SUB BOOST Q-CONTROL FREQ RANGE
X-OVER MODE OPERATION MODE
R
FULL LP MASTER
BALANCED INPUT
Remote wire REM
REM BATT +12V
ATLAS
1 x 600 W/4Ω
1 x 1100 W/2Ω
1 x 1750 W/1Ω
FUSE
POWER INPUT
MASTER/SLAVE-Mode
NOTE: The GENERATION X3 Master/SLAVE-Mode only works with two similar X3-Amplifier-Models.
Ether you link two X3-ATLAS or two X3-CRONOS models.
INTERCONNECTION MASTER
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
• Connect the remote wire (REM) to the remote terminal (REM) of the MASTER amp.
• If required connect the enclosed bass remote wire only on the REMOTE IN port of the MASTER amp.
INTERCONNECTION SLAVE
• Connect the RCA jacks SLAVE IN/OUT of the MASTER amp with the RCA jacks SLAVE IN/OUT of the SLAVE amp with appropriate
high-value RCA cables.
• Connect the remote wire (REM) of the remote terminal (REM) of the MASTER amp with the remote terminal (REM) of the SLAVE amp.
Use therefore cable with a minimum profile section of 0,5 mm
• Connect the PROTECT BRIDGE port of the MASTER amp with the PROTECT BRIDGE port of the SLAVE amp with the encolsed
PROTECT BRIDGE wire.
INTERCONNECTION SUBWOOFER
• Attend page 22.
SETTINGS MASTER
• The OPERATION MODE switch should be in LP position.
Attend therefor the information of LOW PASS, SUB SONIC, PHASE, LEVEL, SUB BOOST, FREQ RANGE, Q-CONTROL and BASS
REMOTE on page 20.
SETTINGS SLAVE
• The MODE switch must be in SLAVE position.
In the SLAVE mode all controllers of the SLAVE amp are without function.
X3-ATLAS / X3-CRONOS X3-ATLAS / X3-CRONOS
Connect the bass remote controller
and the remote terminal on the
MASTER amplifier (REMOTE IN)
with the enclosed cable .
POWER MASTER OUTPUT
SLAVE INPUT LINE OUTPUT
PROTECT
L
PHASE SHIFT SUB SONIC LOW PASS
R
SLAVE
LEVEL REMOTE IN REMOTE OUT
Protect Bridge wire
GND SPEAKER OUTPUT LOGO
BADGE
PROTECT
BRIDGE BLUE
WHITE
e
13
SLAVE MODE 021215
SUBWOOFER
1. Connect Stereo RCA output (L/R or SUB OUT)
of the headunit with the LINE INPUT L/R of the
MASTER amp
2. Connect Stereo RCA output (MASTER OUTPUT)
of the MASTER amp with the SLAVE INPUT of the
SLAVE amp
SLAVE
Switch position = SLAVE
EXTENDED BASS CONTROL
LINE INPUT
L
2.
SUB BOOST Q-CONTROL
X-OVER MODE
R
FULL
BALANCED INPUT
Remote wire REM
ATLAS
1 x 600 W/4Ω
1 x 1100 W/2Ω
1 x 1750 W/1Ω
FUSE
.
2
21
POWER MASTER OUTPUT
SLAVE INPUT LINE OUTPUT
PROTECT
L
FREQ RANGE PHASE SHIFT SUB SONIC LOW PASS
OPERATION MODE
R
LP MASTER SLAVE
LEVEL REMOTE IN REMOTE OUT
Protect Bridge wire
REM BATT +12V GND SPEAKER OUTPUT LOGO
BADGE
PROTECT
BRIDGE BLUE
WHITE
e
13
SLAVE MODE 021215
SUBWOOFER
POWER INPUT