Interconnection Example: Low Pass-Mode (Standard Subwoofer Operation) - Hifonics X3-ATLAS Bedienungsanleitung

INTERCONNECTION EXAMPLE: Low Pass-Mode (Standard Subwoofer Operation)

REM
ATLAS
1 x 600 W/4Ω
1 x 1100 W/2Ω
1 x 1750 W/1Ω
FUSE
NOTE!
A additional subwoofer can be
connected to the non-occupied
speaker outputs. In this case
ensure a impedance of 2 - 8 ohms
per subwoofer.
Subwoofer
1 – 8 Ohm
INTERCONNECTION
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
• Connect the subwoofer with the speaker outputs (SPEAKER OUTPUT + / -) by using appropriate wires.
• Ensure by any means, that the total impedance load of subwoofer is not lower than 1 ohm. Too low impedance cause high
temperature and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
OPERATION MODE SWITCH
• The MODE switch must be in Position MASTER.
X-OVER MODE SWITCH (only X3-ATLAS)
• The X-OVER MODE switch must be in Position LP.
LEVEL CONTROLLER
• Turn the LEVEL controller of the amplifier to the 9V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
EXTENDED BASS CONTROL
• The SUB BOOST controller adjusts the bass enhancement between 0db and +18dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
• Attend therefor the further information (EXTENDED BASS CONTROL) on page 19 (Section #3).
LOW PASS CONTROLLER
• The LOW PASS controller adjusts the cut-off point of the frequency range to above. The cut-off frequency is continuously
adjustable from 40 Hz to 250 Hz.
SUB SONIC CONTROLLER
• The SUBSONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below, to avoid a
mechanical and electrical overloading on the subwoofer. The range is adjustable from 15 to 50 Hz and depends on the size of the
subwoofer.
PHASE CONTROLLER
• The PHASE controller allows to adjust the phasing between 0° and 180°.
Thereby you are able to adjust the subwoofer perfect to the vehicle's acustics.
BASS REMOTE
• The enclosed BASS REMOTE Controller adjusts the bass-level e.g. from the driver's seat.
Please use only the enclosed bass remote controller and cable.
The REMOTE OUT port is suitable to connect the bass remote link cable of an additional amplifier of the HiFONICS X3 Series (only in
MASTER-Mode). Thus to this, you are able to control several amps with only one bass remote.
• Attend therefor the further descriptions REMOTE BRIDGE on page 10.
X3-ATLAS / X3-CRONOS
BATT +12V GND SPEAKER OUTPUT LOGO
BADGE
PROTECT
BRIDGE
BLUE
WHITE
e
13
SLAVE MODE 021215
SUBWOOFER
POWER INPUT
Connect stereo RCA output
(R/L or SUB OUT) of the
headunit with LINE INPUT
EXTENDED BASS CONTROL
LINE INPUT
L
SUB BOOST Q-CONTROL
X-OVER MODE OPERATION MODE
R
FULL LP MASTER
BALANCED INPUT
R/L of the amplifier R
L
20
MASTER OUTPUT
POWER
SLAVE INPUT LINE OUTPUT
PROTECT
L
FREQ RANGE PHASE SHIFT SUB SONIC LOW PASS
R
SLAVE
LEVEL REMOTE IN REMOTE OUT
Switch position =
MASTER
Connect the bass remote
controller and the remote terminal
on the amplifier (REMOTE IN) with
the enclosed cable.