Interconnetion Example Master/Slave-Mode - Hifonics ZXi 1501 Bedienungsanleitung

INTERCONNECTION EXAMPLE Master/Slave Mode
Connect the bass remote
controller and the remote terminal
on the amplifier (MASTER) with
the enclosed cable (REMOTE).
MASTER
Switch setting = LP
PHASE FREQ RANGE Q-CONTROL SUB BOOST
POWER
SLAVE FULL LP
0° 180° 20Hz 80Hz WIDE NRW 0dB 18dB
PROTECT
REMOTE
EXTENDED BASS CONTROL
ZXi 2201
1x1100 Watts
Remote wire REM
GND REM BATT +12V
LOGO
BADGE
BLUE
WHITE
ON
OFF
POWER INPUT
INTERCONNECTION MASTER
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
• Connect the remote wire (REM) to the remote terminal (REM) of the MASTER amp.
• Connect the bass remote wire only on the REMOTE port of the MASTER amp.
INTERCONNECTION SLAVE
• Verbinden Sie die Cinchausgänge (SLAVE OUTPUT) des MASTER-Verstärkers mit den Cincheingängen (LINE INPUT) des
SLAVE-Verstärkers mittels geeigneten hochwertigen Cinch-Audiokabeln.
• Connect the RCA lineouts of the MASTER amp with the RCA jacks LINE INPUT of the SLAVE amp with appropriate high-value
RCA cables.
• Connect the remote wire (REM) of the remote terminal (REM) of the MASTER amp with the remote terminal (REM) of the SLAVE amp.
Use therefore e.g. a loudspeaker wire with a minimum profile section of 0,5 mm
• Connect the PROTECT BRIDGE port of the MASTER amp with the PROTECT BRIDGE port of the SLAVE amp with the encolsed
PROTECT BRIDGE wire.
INTERCONNECTION SUBWOOFER
• Attend page 22.
SETTINGS MASTER
• The MODE switch should be in LP position.
Attend therefor the information of LOW PASS, SUB SONIC, PHASE, LEVEL, SUB BOOST, FREQ RANGE, Q-CONTROL and BASS
REMOTE on page 20.
• As option the FULL RANGE mode is also available.
Attend therefor the information on page 23.
SETTINGS SLAVE
• The MODE switch must be in SLAVE position.
ZXi1501 · ZXi2201
1.
SUB SONIC LOW PASS LEVEL SLAVE OUTPUT LINE INPUT
MODE L L
15Hz 55Hz 35Hz 250Hz 9V 0.2V
R R
2.
PROTECT
+ + – –
FUSE
BRIDGE
SPEAKER OUTPUT
1. Connect Stereo RCA output (CH1/2 L/R or
SUB OUT) of the headunit with the
LINE INPUT CH1/2 of the amplifier (MASTER)
2. Connect Stereo RCA cable (SLAVE OUT) of
the amplfier (MASTER) with the LINE INPUT of
Remote wire REM
the amplifier (SLAVE)
PHASE FREQ RANGE
POWER
0° 180° 20Hz
PROTECT
REMOTE
ZXi 2201
1x1100 Watts
Remote wire REM
Protect Bridge wire
GND REM
LOGO
BADGE
BLUE
WHITE
ON
OFF
POWER INPUT
.
2
21
SLAVE
Switch setting = SLAVE
Q-CONTROL SUB BOOST SUB SONIC LOW PASS LEVEL SLAVE OUTPUT LINE INPUT
MODE L L
SLAVE FULL LP
80Hz WIDE NRW 0dB 18dB 15Hz 55Hz 35Hz 250Hz 9V 0.2V
EXTENDED BASS CONTROL
R R
PROTECT
+ + – –
BATT +12V
FUSE
BRIDGE
SPEAKER OUTPUT