Vertical Steam - Siemens slider SL45 Gebrauchsanleitung

en

Vertical steam

This can be used to remove creases from hanging
clothes, curtains etc.
Warning!:
• Never direct the steam jet at garments that are
being worn.
• Never aim the steam at people or animals.
1. Set the temperature to the
2. Hold the iron in an upright position 15 cm away from
the garment being steamed.
3. You can steam iron curtains and hanging garments
(jackets, suits, coats...) by placing the iron in a
vertical position and pressing the steam release
button (13 or 14*).
"Intelligent steam" function.
(model dependent)
This system has intelligent steam control, which, after
releasing the steam release button (13), provides a
small amount of additional steam.
The additional steam can always be stopped by briefly
pressing the steam release button once again.
Energy saving
"eco" button
If the "Energy saving" button (7*) is switched on, you
can save up to 25% of the energy and 40% of the water
consumption (*), and still achieve good results when
ironing most of your garments.
It is advisable to use the normal energy setting only for
thick and very wrinkled fabrics.
(*) In comparison to the maximum setting.
Note:
If you work with the "Energy saving" function,
the variable steam regulation and temperature
regulation can still be used as recommended.
"secure" auto shut-off
(model dependent)
If during ironing, the steam release button (13-14*) on
the iron handle is not pressed for a certain length of
time (8 minutes), the steam station will automatically
switch off.
The " " icon will flash when auto shut-off has
been activated.
To switch the steam station back on, press the steam
release button again.
16
(D) Fabric protection soleplate cover (E)
(model dependent)
The fabric-protection soleplate cover (17*) is used
for steam ironing delicate garments at maximum
temperature without damaging them. Use of the
soleplate cover also does away with the need for a
cloth to prevent shine on dark materials.
It is advisable to first iron a small section on the inside
setting.
of the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip of
the iron into the end of the soleplate cover and pull the
elastic strap over the lower rear of the iron until it fits
tightly. To release the soleplate cover, pull the elastic
strap and remove the iron.
The fabric-protection soleplate cover may be purcha-
sed from our customer service or from our website:
Descaling the filter
and the boiler (F)
(calc'nClean Plus)
To extend the life of your steam generator and to
prevent any build up of scale, it is essential that you
rinse out the filter (12) and the boiler after a period of
use. If the water is hard, increase the frequency.
Do not use descaling agents for rinsing out the boiler,
as they could damage it.
If the "
must be rinsed. Please proceed as follows:
1. Check carefully that the appliance is cold and
2. Fix the iron to the base by inserting the tip of the iron
3. Place your appliance over a sink or bucket.
4. Lean the appliance on the opposite side of the filter
5. Unscrew the filter (12) and take it out.
6. To wash the filter, you may:
Accessory code Name of accessory
(After-sales)
571510
" icon flashes, this indicates that the boiler
unplugged for more than 2 hours, and that the water
tank (1) is empty.
into the front slot and moving the secureLock lever
(10) against the heel of the iron.
opening.
a. Place the filter under the water tap and wash it
until calc residues are removed. Squeeze the filter
as indicated in the picture F.
b. Immerse the filter in tap water (250 ml) mixed with
a measure (25 ml) of descaling fluid. Rinse filter
thoroughly before placing it back into the boiler
The descaling fluid can be obtained from our After-
sales service or from our website.
Accessory code
(After-sales)
311144
(Online shop)
TZ20450
Name of accessory
(Online shop)
TZ11001