Pioneer DEH-2200UBB Installationsanleitung Seite 5

Connections
1 This product 14 Rear output
4 Note:
Depending on the kind of vehicle, the function
2 Antenna
of 2* and 4* may be different. In this case, be
jack
sure to connect 1* to 4* and 3* to 2*.
3 Fuse (10 A)
5 Wired remote input
2* 1*
Hard-wired remote
control adaptor can
be connected (sold
separately).
4* 3*
6 Connect leads of the same
color to each other.
7 Yellow (2*) 8 Yellow (1*)
Back-up Connect to the constant 12 V
(or accessory) supply terminal.
9 Red (4*) 10 Red (3*)
Accessory Connect to terminal controlled by
(or back-up) ignition switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
13 Speaker leads
In some vehicles, the ISO connector may be
White: Front left
divided into two. In this case, be sure to
White/black: Front left
connect to both connectors.
Gray: Front right
Gray/black: Front right
Green: Rear left
Green/black: Rear left
Violet: Rear right
Violet/black: Rear right
En
Connections
21 Power amp
(sold separately)
19 To Rear output
20 Connect with RCA cables
(sold separately)
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
22 System remote control
17 Blue/white (6*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
18 Blue/white (5*)
The pin position of the ISO connector will
23 Left 24 Right
differ depending on the type of vehicle.
Connect 5* and 6* when Pin 5 is an
25 Rear speaker 25 Rear speaker
antenna control type. In another type of
vehicle, never connect 5* and 6*.
26 Perform these connections when using
the optional amplifier.
En
Connections
— Never band together negative cables of
Important
multiple speakers.
! When installing this unit in a vehicle without
! When this unit is on, control signals are sent
an ACC (accessory) position on the ignition
through the blue/white cable. Connect this
switch, failure to connect the red cable to the
cable to the system remote control of an exter-
terminal that detects operation of the ignition
nal power amp or the vehicle's auto-antenna
key may result in battery drain.
relay control terminal (max. 300 mA 12 V DC).
If the vehicle is equipped with a glass anten-
na, connect it to the antenna booster power
supply terminal.
! Never connect the blue/white cable to the
power terminal of an external power amp.
ACC position No ACC position
Also, never connect it to the power terminal of
! Use of this unit in conditions other than the
the auto antenna. Doing so may result in bat-
following could result in fire or malfunction.
tery drain or a malfunction.
— Vehicles with a 12-volt battery and negative
! The black cable is ground. Ground cables for
grounding.
this unit and other equipment (especially,
— Speakers with 50 W (output value) and 4
high-current products such as power amps)
ohm to 8 ohm (impedance value).
must be wired separately. If they are not, an
! To prevent a short-circuit, overheating or mal-
accidental detachment may result in a fire or
function, be sure to follow the directions
malfunction.
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or ad-
Connection Diagram (Fig. 1)
hesive tape. Wrap adhesive tape around
wiring that comes into contact with metal
1 This product
parts to protect the wiring.
2 Antenna jack
— Place all cables away from moving parts,
3 Fuse (10 A)
such as the gear shift and seat rails.
4 Note:
— Place all cables away from hot places,
Depending on the kind of vehicle, the function
such as near the heater outlet.
of 2* and 4* may be different. In this case, be
— Do not connect the yellow cable to the bat-
sure to connect 1* to 4* and 3* to 2*.
tery by passing it through the hole to the
5 Wired remote input
engine compartment.
Hard-wired remote control adaptor can be
— Cover any disconnected cable connectors
connected (sold separately).
with insulating tape.
6 Connect leads of the same color to each
— Do not shorten any cables.
other.
Fig. 1
— Never cut the insulation of the power cable
7 Yellow (2*)
Abb. 1
of this unit in order to share the power
Back-up (or accessory)
Afb. 1
with other devices. The current capacity of
8 Yellow (1*)
Рис. 1
the cable is limited.
Connect to the constant 12 V supply terminal.
— Use a fuse of the rating prescribed.
9 Red (4*)
— Never wire the negative speaker cable di-
Accessory (or back-up)
rectly to ground.
En
Connections
10 Red (3*)
Connect to terminal controlled by ignition
switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.
13 Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left +
Green/black: Rear left *
Violet: Rear right +
Violet/black: Rear right *
14 Rear output
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
17 Blue/white (6*)
Connect to auto-antenna relay control term-
inal (max. 300 mA 12 V DC).
18 Blue/white (5*)
The pin position of the ISO connector will dif-
fer depending on the type of vehicle. Connect
5* and 6* when Pin 5 is an antenna control
type. In another type of vehicle, never connect
5* and 6*.
19 To Rear output
20 Connect with RCA cables (sold separately)
21 Power amp (sold separately)
22 System remote control
23 Left
24 Right
25 Rear speaker
26 Perform these connections when using the
optional amplifier.
En