Troubleshooting; Technical Data - Clatronic wk 3098 Bedienungsanleitung

1. Place the machine on a fl at surface.
2. Please use the handle in the lid to open the kettle. Then fi ll
in the water. Please only fi ll up to the maximum (MAX) mark.
You can check the level on both sides of the appliance with
the water level display.
3. Close the lid until you hear it lock in place.
4. Place the kettle fl ush on the base.
5. Electrical connection
• Check whether the electrical voltage that you intend to
use is the same as that of the machine. Details are to be
found on the label on the base.
• Only connect the machine to a properly installed 230 V,
50 Hz safety socket.
6. Switch on the kettle by pressing the switch. To control lamp
lights up.
7. After boiling has fi nished the kettle switches off automati-
cally, or you can push the switch upwards to interrupt or stop
the boiling process.
WARNING: Danger of scalding!
• When pouring the water out, keep the lid closed.
• During operation the housing becomes hot. Do not touch it
and allow the device to cool down before storing it away.
Switching off
• If you would like to turn the kettle off, push the switch up-
wards (0) and remove the plug from the socket. The control
lamp goes off.
• Emptying the water container.
Mains Cable Take-up Device
The mains cable can be wound up on the base.
Cleaning
WARNING:
• Always turn the device off before cleaning it and remove
the mains plug. Wait until the device has cooled down.
• Never immerse the device or the base in water or other
liquids.
CAUTION:
• Do not use any wire brush or other abrasive objects.
• Do not use any acidic or abrasive detergents.
Water Container
• Rinse the water container out with clean water. Then dry it
off with a cloth.
Exterior of the Housing
• Clean the housing after use with a slightly damp cloth.
• There is a permanent fi lter in the spout. In order to clean the
fi lter, pull it out with the lid open. Rinse out the fi lter with run-
ning water. Reinsert it, taking note of the guide mechanism.
05-WK 3098 Neu.indd 23 05-WK 3098 Neu.indd 23
Use Decalcifi cation
• The frequency of the decalcifying operation depends on the
hardness of the water and on how often the appliance is
used.
• If the machine switches off before the water boils, it probably
needs to be decalcifi ed.
• Please do not use vinegar but a commercially available
decalcifi cation agent on the basis of citric acid. Only use the
quantities stated in the instructions.
NOTE:
After descaling the device boil fresh water in it several times
(approximately 3-4 times) in order to remove any residues. Do
not consume this water.

Troubleshooting

• It is not possible to switch the machine on.
Possible Cause:
After being used without or with too little water the machine
has not cooled down suffi ciently.
Remedy:
Allow the machine to cool down for 15 min.
• The machine switches off before the water has boiled.
Possible Cause:
The heated base is coated with too much lime or the circuit
of the plug is overloaded.
Remedy:
Descale the machine as instructed.
Check the mains connection.
• The machine does not switch off.
Possible Cause:
The lid is not closed.
Remedy:
Close the lid until it locks in place.

Technical Data

Model: ..............................................................................WK 3098
Power supply: ............................................................230 V, 50 Hz
Power consumption: ..........................................................2200 W
Protection class: ........................................................................... Ι
Filling quantity: .........................................................max. 1,7 Litre
Net weight: ........................................................................0,75 kg
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
23
08.05.2009 8:23:59 Uhr 08.05.2009 8:23:59 Uhr