Supplementary Screen Displays - GRAUPNER ULTRA DUO PLUS 80 Bedienungsanleitung

In the active screen area (standard appearance) you can switch
between the various displays using the MODE or ESC button. The
settings apply to the selected charge output only.
User settings:
This display enables the user to select the temperature display (TEMP MODE: °C or °F), the button beeps (BUTTON
SOUND: on / off), the length of the melody (FINISH SOUND: on / off, 15 sec.- 1 min.) and the melody (MELODY 1 - 9) which
is to sound at the end of the charge process. We recommend that you select different melodies for the two charge outputs,
so that you can immediately tell from the tune which battery is fully charged.
Data view:
This display shows the charger's input voltage (INPUT VOLT) and output voltage (OUTPUT VOLT), and - if the temperature
sensor is connected - the actual temperature (BAT.TEMP) and maximum temperature (PEAK TEMP.) of the selected charge
output.
Cycle view:
This display shows the charge data (C) and discharge data (D) for the last battery which was cycled at this output. The
display shows charged-in and discharged capacity in mAh and voltage in V.
Note: the Cycle menu is only available for NiCd and NiMH batteries; you can view the data for the last ten cycles by pressing
the INC button.
Operating Manual ULTRA DUO PLUS 80

11. Supplementary screen displays

MEMORY SET
display
11] LiPo 3S 2200mAh

STORE MODE START
CHG. : 2.1 A 4.20V/C
DCHG. : 10.0A 3.0V/C
0 ] NiMH 6S 3300mAh

CYCLE : C-> D 1X
CHG. : 3.3A 5mV/C
DCHG. : 5.0A 0.8V/C
USER SET DATA VIEW
display display
TEMP.MODE : °C INPUT VOLT: 13.200V
 
BUTTON SOUND : ON OUTPUT VOLT: 11.123V
Mode
Mode
FINISH SOUND : 5sec BAT. TEMP. : No.Sens
MELODY : 1 PEAK TEMP. :
0 ] NiMH 6S 3300mAh 0 ] NiMH 6S
 
10m CYCLE : C-> D 1X 10m
CYCLE : C->
ESC
ESC CHG. : 3.3A 5mV/C CHG. : 3.3A
DCHG. : 5.0A 0.8V/C DCHG. : 5.0A
CYCLE VIEW BALANCER VIEW
display display
[ 1]CAPACITY VOLTAGE 3S=11.845V
Mode C: 0mAh 0.000V Mode 33.95V
3
D: 0mAh 0.000V 13.94V
1
0.0°C
3300mAh 0 ] NiMH 6S 3300mAh 0 ] NiMH
 
D 1X 10m CYCLE : C-> D 1X 10m CYCLE
ESC ESC
5mV/C CHG. : 3.3A 5mV/C CHG.
0.8V/C DCHG. : 5.0A 0.8V/C DCHG.
TEMP.MODE :

BUTTON SOUND :
FINISH SOUND :
MELODY :
0 ] NiMH 6S

CHG. : 3.3A
DCHG. : 5.0A
CYCLE : C-> D
INPUT VOLT: 13.200V

OUTPUT VOLT: 11.123V
BAT. TEMP. : No.Sens
PEAK TEMP. :
0 ] NiMH 6S

CHG. : 3.3A
DCHG. : 5.0A
CYCLE : C->
[ 1]CAPACITY VOLTAGE
1
C: 0mAh
D: 0mAh
0 ] NiMH 6S

CHG. : 3.3A
DCHG. : 5.0A
CYCLE : C->
1S=3.944V
1
8mV
6S 3300mAh
: C-> D 1X 10m
: 3.3A 5mV/C
: 5.0A 0.8V/C
°C
ON
5sec
3300mAh
5mV/C
0.8V/C
1X 10m
0.0°C
3300mAh
5mV/C
0.8V/C
0.000V
0.000V
3300mAh
5mV/C
0.8V/C
41