INTUO E 01-K Gebrauchsanleitung Seite 21

woRKToPS
tHe surfaces of all of our WorktoPs coMPly WitH tHe guiDelines for tHe use of kitcHen WorktoPs.
WorktoPs are subjecteD to tHe Most Wear anD tear in a kitcHen, esPecially tHe front eDge of tHe
WorktoP. tHis inevitable Wear is not a flaW. scratcHes anD Wear are More obvious on a Dark, soliD-
coloureD WorktoP tHan on a Multi-coloureD WorktoP. tHis is not consiDereD grounDs for coM-
Plaint.
even tHougH tHe WorktoP is HigHly Heat-resistant, Hot Pots anD Pans Must not be PlaceD Directly
on tHe WorktoP surface. any DaMage resulting froM iMProPer HanDling of Hot Pots anD Pans is not
consiDereD grounDs for coMPlaint.
tHe surface of tHe WorktoP is 100% Moisture-resistant, anD tHe joints Have been Professionally
sealeD. floWer Pots, coffee anD esPresso Makers, electric kettles, anD any sucH aPPliances tHat
Present a Danger of overfloWing sHoulD not be PlaceD on tHe joints. iMMeDiately WiPe uP any sPilt
Water.
LAmINATED woRKToPS
(mELAmINE RESIN)
laMinateD WorktoPs are best cleaneD WitH conventional HouseHolD cleansers or siMPly WitH luke-
WarM Water, soMe DisHWasHing liQuiD anD a soft cotton clotH. sPots anD sPills Must be reMoveD
iMMeDiately before tHey Dry. Water sPots can be avoiDeD by WiPing tHe surface WitH a Dry, soft
clotH after cleaning. stubborn sPots like fat sPlatters or glue resiDue can be reMoveD WitH a
stanDarD cleanser for cleaning Plastics. before use, test tHe cleanser on a HiDDen sPot. abrasive
cleansers or PolisH, HarD, scratcHy sPonges, brusHes anD Microfiber clotHs are not suitable for
cleaning laMinateD WorktoPs. Do not use cleansers tHat contain acetone, cHlorinateD HyDrocar-
bon, Paint tHinner or solutions tHat begin WitH tHe syllabes "tri" or "tetra".
mINERAL mATERIAL woRKToPS
tHe aDvantage of Mineral Material WorktoPs is tHat sucH surfaces can be rePaireD. sMall scrat-
cHes, Dents anD stubborn sPots can be reMoveD or grounD DoWn, WHicH restores tHe original
state of tHe Plate. Please folloW instructions for tHe cleaning anD care of WorktoPs coateD WitH
syntHetic Materials (MelaMine resin).
040-041 EN
Do not Place any floWer Pots, coffee or esPres-
so Makers, electric kettles or any sucH aPPlian-
ces tHat Present a Danger of overfloWing on tHe
joints. iMMeDiately WiPe uP any sPilt Water.
tHe DisHWasHer sHoulD not be oPeneD until about
30 Minutes after tHe last cycle. oPening it ear-
lier releases Heat anD steaM, WHicH in tHe long
run DaMages tHe aDjacent fronts, carcase coM-
Ponents, anD eDges, as Well as tHe unDersiDe of
tHe WorktoP – in sPite of tHe use of HigH-Quality
Materials anD Meticulous WorkMansHiP. DaMage
tHat is causeD by iMProPer use is not consiDereD
grounDs for coMPlaint. for DisHWasHers WitH an
acoustic signal announcing tHe enD of tHe last
cycle, Do not oPen tHe aPPliance for 30 Minutes
after tHe signal goes off.
control regularly tHe silicon sealings along
tHe back Panels, arounD tHe sink anD at tHe
WorktoP units. it's iMPortant not to scratcH
tHe sealings WHen cleaning; DaMageD seals
Must be rePlaceD. Possible Water DaMages as
a result of DaMageD sealings are no reason
for coMPlaints.