INTUO E 01-K Gebrauchsanleitung Seite 18

HIGH GLoSS ACRYLIC FRoNTS
ProDuct cHaracteristics: acrylic is a syntHetic tHerMoPlastic Material WitH a HigH gloss surface.
tHe surfaces are ProtecteD During transPort anD installation WitH a PolyetHylene Protective foil
WitH a sPecial unDercoating. surface cHaracteristics: colour, colour uniforMity anD DePtH ef-
fect are essential Quality cHaracteristics of tHe acrylic HigH gloss surface. care after Mounting:
During Processing anD transPort, tHe acrylic HigH gloss surface is ProtecteD WitH a self-aDHesive
PolyetHylene Protective foil tHat is only reMoveD WHen tHe kitcHen Has been coMPletely MounteD
for tHe enD-user. after tHe Protective foil is reMoveD, tHe acrylic HigH gloss surface is still sensi-
tive. natural air HuMiDity Will HarDen tHis. tHis can take uP to a Week. to accelerate tHis HarDening
Process anD to acHieve a HarD-Wearing surface, seal tHe fronts iMMeDiately after reMoving tHe
Protective foil WitH tHe ProviDeD PolisH (*ug-PolisH). use a soft clotH (no Microfibre clotH).
CARE INSTRUCTIoNS
1. tHe surface to be PolisHeD Must first be cleaneD WitH a 1% soaP solution (e.g. 5 l of Water MixeD
WitH 5 cl soaP solution) anD tHorougHly DrieD.
2. before using tHe PolisH (*ug-PolisH), sHake Well.
3. aPPly tHe PolisH (*ug-PolisH) to tHe surface evenly anD WitH sligHt Pressure WitH a clean soft
clotH or PolisHing sPonge.
note: a little of tHe PolisH (*ug-PolisH) goes a long Way, so use sParingly.
4. Directly after aPPlication, tHe PolisH (*ug-PolisH) can be reMoveD WitH a soft clean clotH
(no Microfibre clotH) in straigHt-line MoveMents. noW tHe surface Has been given a HigH gloss
anD a long-lasting sealing.
FURTHER CARE AND CLEANING
- tHe surface sealing sHoulD be rePeateD WitH *ug-PolisH once a year, folloWing tHe care
instructions.
- for regular cleaning, use an antistatic cleanser for Plastics or a 1 % soaP solution (e.g. 5 l Water
MixeD WitH 5 cl soaP solution). use a soft clotH (no Microfibre clotH).
iMPortant note:
Do not use glass cleaners, abrasive cleansers, Microfibre clotHs or cleaning agents containing
alcoHol. recoMMenDeD cleaner: *ug-PolisH
- ug-PolisH 50 Ml Has been ProviDeD free of cHarge WitH your kitcHen (enougH for 6 – 10 sQuare
Metres).
- for furtHer Perfect care of tHe acrylic HigH gloss surface, ug-PolisH 250 Ml anD PolisHing sPonge
are available froM your kitcHen retailer.
034-035 EN
abrasive cleansers, anD PolisHes, as Well as
HarD, scratcHy sPonges, brusHes or Micro-
fibre clotHs are not suitable for cleaning
acrylic fronts. never use cleansers tHat
contain acetone, cHlorinateD HyDrocarbon,
Paint tHinner or solutions tHat begin WitH tHe
syllables "tri" or "tetra".
WHile cooking, Make sure tHat any extra steaM
is extracteD WitH a cooker HooD. in tHe long
run, Heat anD steaM can DaMage aDjacent units,
fronts or eDges, in sPite of tHe use HigH-Quality
Materials anD Meticulous WorkMansHiP. DaMage
tHat is causeD by iMProPer use is not consiDereD
reasons for coMPlaint.