Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Setting the grill
In this section, you can find out how to set the grill.The table
shows grill settings and cooking times for various meals.
Switching the grill on and off
The main switch is used to switch the grill on and off.
To switch on: Touch the
#
display above the main switch lights up. The grill is ready to
use.
To switch off: Touch the
#
main switch goes out. The grill has been switched off. The
residual heat display remains lit until the grill has cooled down
sufficiently.
Note: The grill switches off automatically when the grill setting
remains at 0 for more than approx. 15 seconds.
Setting the grill
Set the desired grill setting on the control panel.
Grill setting 1 = lowest output
Grill setting 9 = highest output
Setting the grill setting
Note: You can decide whether the heating zones should be
linked or not when the appliance is switched on; see Basic
settings.
Switch on the grill using the main switch.
1.
To select a grill element, touch the
2.
next to the
Ò
or
Ó
symbol.
A bar lights up under the grill settings display for the selected
grill element.
Touch the
symbol.
þ
3.
A bar lights up for both grill elements under the grill settings
displays. Both grill elements are linked. The same grill setting
is set for both grill elements.
Touch the
symbol.
þ
4.
The link between both grill elements is cancelled again.
Set the desired grill setting on the settings range using the
5.
and
symbols.
A
Touch the
symbol.
@
6.
lights up in the grill setting display.
Š
Or:
Touch the
symbol.
A
...
lights up in the grill setting display.
The
heating symbol lights up.
}
As soon as the set temperature has been reached, a signal
sounds and the
}
heating symbol goes out.
Note: The grill regulates the temperature by switching the grill
element on and off. The grill element may be switched on and
off even at the highest setting.
symbol. A signal sounds. The
symbol until the display above the
‹
grill settings display
Pre-heating the grill
Do not place the food to be grilled onto the grill until the pre-
heating time has elapsed. The heating symbol goes out. During
the pre-heating time, the grill heats at full power. Once the pre-
heating time has elapsed, the temperature is reduced by
switching the heating element on and off in order to achieve a
constant temperature for the relevant setting.
The pre-heating time is between 6 and 10 minutes, depending
on the grill setting which has been set.
Note: Do not leave the empty grill to heat up at the highest grill
setting for a prolonged period of time (approx. 6 – 10 minutes).
Heating up for prolonged periods of time may lead to the
appliance shutting down (overheating protection). Switch off the
appliance and allow it to cool down before you switch it back
on again.
Topping up the water
If there is too little water in the grill container, the overheating
protection switches the appliance off. Therefore, while grilling,
monitor the water level in the grill container and top it up as
necessary.
Grilling with lava stones: bottom mark
Grilling without lava stones: top mark
:
Risk of scalding!
If water touches the hot wire grilling rack or grill element during
topping up, hot steam will be generated. Do not reach over the
grill while topping up and do not pour water over the hot
components.
Switching Wipe protection on and off
When the appliance is in use, you can activate the key lock for
approx. 30 seconds using the Wipe protection function in order
to clean the control panel.
Touch the
symbol to switch Wipe protection on.
"
1.
Note: When Wipe protection is switched on, all symbols are
locked, except for the
@
symbol for switching off the appliance.
The displays above the
light up.
Clean the control panel with water and washing-up liquid.
2.
Touch the
symbol to switch off Wipe protection.
"
3.
Wipe protection symbol and the
"
symbol and above the
"
#
symbol
#
17
Werbung
Kapitel
Inhaltsverzeichnis
