Safety Notice - Vitavia Calypso 4400 Montageanleitung

them."
Push the door gliders (1014) onto both ends of
door bar (1360) (5.1).
Assemble the door as shown in diagram 5.
Connect door rollers (1015) to the door bar
(1362) using bolt (1304), washer (1009) and
nut (1007) (5.4). Bolt door bar (1362) to upper
bar (1359) (5.3) and slide the door seal (1021)
into both side bars (1358) (5.6).
The door rollers can now slide into door
runner bar (1347) (5.7). Please ensure that the
door gliders are also running on the bottom
track (5.5). Once the door is correctly in place,
connect a nut and bolt into the end of door
runner bar (1347) as door stopper.
Adjust the door so that it moves freely.
6. RooF VeNtS
Connect the side bars (1065) and the top bar
(1088) depending on the glass thickness.
Up to 4 mm, see (6.1). For 4 mm and over,
see (6.2).
Place the bolts to connect the bottom bar
(1090) in the prepared holes, and then slide
the glass into the tracks in side bars (1065)
(6.3).
Now connect bottom bar (1090), and ensure
that the window is totally square before
tighten ing all bolts.
Position the window in the ridge bar from one
end (6.4) and (6.5) and slide it to the required
position (6.6).
Connect the window sill (1087) with the extra
bolts in the roof glazing bars (6.7). If the
window is connected in a corner position, then
it is necessary to use bolt (2001), instead of
(1001), on the corner bar.
Bolt the window opener (1067) to the bottom
bar (1090) (6.7) using screws (1006) (6.8).
Place the plastic cap (1019) over the end of
the window opener (6.6) and connect both
window fixers (1016) onto the window sill
(1087) using screws (1006) (6.8).
7. GlazING – PolycaRBoNate PaNeS
Please note the already mentioned safety
precautions.
Important! The UV-resistant side is indicated
by the plastic folio and printing at the edge.
this side must face outside.
Remove the folio. Note! Completely remove
the folio only after the pane has been
positioned in the greenhouse. (The panes are
042.01.1206
cut marginally shorter to allow for expansion in
warm conditions).
Press the glazing seals (1020) onto the
aluminium profiles (7.2) and cut to length.
Fix the glazing panes in place using the
glazing spring clips (1011) (7.1) and note the
quantity required on each pane.
In order to give the Polycarbonate panes extra
stability, it is recommended to connect them to
the bottom aluminium profile, in the middle of
each pane, with a screw and washer (7.3). To
achieve this it is necessary to drill a 2mm hole
through the pane and the aluminium profile.
The drill is not included.
The panes in the 7B Gabels should be
connected using the H -plastic (4mm 24674 /
6mm 24686) as shown.
FINIShING
If desired, it is possible to seal the greenhouse
at the edges using neutral silicone. Silicone is
not in cluded.
Place the warning label inside the house.
A full range of greenhouse accessories, to help
you make the most of this product, is available
from your stockist. Please inform yourself as to
the possibilities.

SaFety NotIce

In the event of high wind conditions, close the
door and all vents.
In the event of heavy snowfall, clear the roof
of the building or take suitable measures to
support the roof. Heat the building in winter.
commeNtS
For the complete protection of your new
greenhouse, we advise you to include it in
your house insurance. Please take note of
possible building rules relating to the position-
ing of greenhouses.
Please stick the included greenhouse model
label onto the door bar (1362) after success-
fully assembling this product. This information
is important in the event that replacement
parts are later required.
Please keep these Assembly Instructions in
a safe place, for future reference!
Our policy is one of continuous improvement
and we reserve the right to change the specifi-
cations without prior notice.
5