Safety Notice - Vitavia DIANA 9900 Montageanleitung

loosely. Adjust the greenhouse until it is
completely square and tighten all bolts. Please
do not over tighten.
Press the end protectors (1017) onto the eave
ends (4.10).
5R and 5L DOOR
Attention: Do not stand the assembled
door on the door gliders (1014) to avoid
damaging them.
Push the door gliders (1014) onto both ends of
door bar (1060) (5.1).
Assemble the door as shown in diagram 5.
Connect door rollers (1015) to the door bar
(1062) using bolt (1004), washer (1009) and
nut (1007) (5.4). Bolt the door bar (1062) to
upper bar (1059) (5.3) and slide the door seal
(2021) into the outside side bar (5058) (5.6).
Please ensure that for the inside side bar, the
part (5098) is used on the right in 5R and
(5099) on the left in 5L.
Connect the door fixer (1111) as shown.
Loosen the door supports (5043).
The door rollers can now be slid into door
runner bar (5047) (5.7). Please ensure that the
door gliders are also running on the bottom
track (5.5).
Once the doors are correctly in place, connect
a nut and bolt into the ends of door runner
bars (5047) as door stoppers.
Adjust the doors so that they move freely.
6. ROOF VENTS
Connect the side bars (1065) and the top bar
(1064) depending on the glass thickness.
Up to 4 mm, see (6.1). For 4 mm and over,
see (6.2).
Place the bolts to connect the bottom bar (1066)
in the prepared holes, and then slide the glass
into the tracks in the side bars (1065) (6.3).
Now connect bottom bar (1066), and ensure
that the window is totally square before
tightening all bolts.
Position the window in the ridge bar from one
end (6.4) and (6.5) and slide it to the required
position (6.6).
Connect the window sill (1063) with the extra
bolts in the roof glazing bars (6.7).
Bolt the window opener (1067) to the bottom
bar (1066) (6.6) using screws (1006) (6.8).
Connect both window fixers (1016) onto the
window sill (1063) using screws (1006) (6.7).
Place the plastic cap (1019) over the end of
the window opener (1067).
006.00.0811
7A. and 7B. GLAZING –
CLEAR/FROSTED GLASS
Please note the already mentioned safety
precautions and the glazing method pro-
vided, "A" or "B".
Press the glazing seals (1020) onto the alu-
minium profiles (7.2) and cut to length.
On the roof, begin by positioning the glass at
the ridge and fix in place using the glazing
spring clips (1011) (7.1).
For glazing method 7A the following pane
should slide under the pane directly above it
with the glass retaining clips (1012) between
the panes (7.3).
Connect the acrylic glass to the last glass
pane using glass retaining clips (1012) (7.3)
and then bend it over the curved section fixing
with spring clips (1011) (7.1). If difficulties arise
in placing the last pane, please ensure that
those above have not slipped down.
On the sides please begin from the bottom.
When glazing the front or back, fit part (5012)
as shown on pane 5 and bend it up to fix
upper panes 6 or 8 (7.4).
It is possible to replace a lower side pane
(for 7A pane 5, for 7B change one pane 5 with
pane 5a) with a louver window. The louver is
not included.
FINISHING
If desired, it is possible to seal the greenhouse
at the edges using silicon. Silicon is not in cluded.
Place the warning label inside the house.
A full range of greenhouse accessories, to
help you make the most of this product, is
available from your stockist. Please inform
yourself as to the possibilities.

SAFETY NOTICE

In the event of high wind conditions, close the
doors and all vents.
In the event of heavy snowfall, clear the roof
of the building or take suitable measures to
support the roof. Heat the building in winter.
COMMENTS
For the complete protection of your new
green house, we advise you to include it in
your house insurance. Please take note
of possible building rules relating to the
positioning of greenhouses.
Please stick the included greenhouse model
label onto the door bar (1062) after success-
fully assembling this product. This information
is important in the event that replacement
parts are later required.
Please keep these Assembly Instructions in a
safe place, for future reference!
Our policy is one of continuous improvement
and we reserve the right to change the specifi-
cations without prior notice.
5