Know Your Product; Operation - Sparky Professional HeavyDuty BVR 62E Originalbetriebsanleitung

▪ Remove all nails, screws and other objects from the
work piece.
▪ Before using the tool on an actual workpiece, switch
on and let it run for a while. Operate the tool at least
200 mm away from your face and body.
▪ Always be sure you have a firm footing. Be sure no
one is below when using the tool in high locations.
▪ Hold the tool firmly. Keep hands away from rotating
parts. Do not touch the bit or the work piece immedi-
ately after operation: they may be extremely hot and
could burn your skin.
WARNING: Before connecting a tool to a
power source (mains socket power point receptacle,
outlet, etc.) be sure that the voltage supply is the same
as that specified on the nameplate of the tool.
.
▪ A power source with a voltage greater than that speci-
fied for the tool can result in serious injury to the user,
as well as damage to the tool.
▪ If in doubt, do not plug in the tool.
▪ Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
jury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operat-
ing instructions found in this Manual. All persons who
use and service the machine have to be acquainted
with this Manual and must be informed about its po-
tential hazards. Children and frail people must not use
this tool. Children should be supervised at all times if
they are in the area in which the tool is being used. It
is also imperative that you observe the accident pre-
vention regulations in force in your area. The same
applies for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
Even when the tool is used as prescribed it is not pos-
sible to eliminate all residual risk factors. The following
hazards may arise in connection with the tool's construc-
tion and design:
- Damage to hearing if effective hearing protection is
not worn.
- Always remove the plug from the mains socket be-
fore making any adjustments or maintenance, includ-
ing changing the operating accessories and adjusting
the depth of screwing.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.
Original instructions
pages-BVR6xE-2017.indd 5

Know your product

Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Screwdriver bit / Socket
2. Cap / Screw depth stop
3. Adjustment collar
4. Belt clip
5. Reversing switch
6. Speed controller
7. On/Off switch
8. Locking button for on/off switch

Operation

This model SPARKY power tools is supplied from single-
phase alternating current mains. It is double insulated ac-
cording to EN 60745-1, IEC 60745 and can be connected to
grounded or not grounded sockets. This power tool is radio
suppressed in compliance with EMC Directive.
PRIOR TO INITIAL OPERATION
▪ Make sure power supply voltage corresponds to the
value indicated on the name plate with technical data of
the tool.
▪ Always check the position of ON/OFF switch. The power
tool must be connected to the power supply socket only
when this switch is in OFF position. If the plug is connect-
ed to a receptacle while the power switch is in the ON
position, the power tool will start operating immediately,
which could cause a serious accident.
▪ Make sure the cord and the plug are in order. If the re-
placement of the supply cord is necessary, this has to be
done by the manufacturer or his agent in order to avoid a
safety hazard.
WARNING: Always be sure that the tool is
switched off and unplugged before adjusting or check-
ing function on the tool.
Fit the screw on the point of the bit and place the point
of the screw on the surface of the work piece to be fas-
tened. Apply pressure to the tool and start it. Withdraw
the tool as soon as the clutch cuts in. Then release the
switch trigger. (Fig. 1)
WARNING: When fitting the screw onto the
point of the bit, be careful not to push in on the screw.
If the screw is pushed in, the clutch will engage and
the screw will rotate suddenly. This could damage a
work piece or cause an injury. Make sure that the bit is
inserted straight in the screw head, or the screw and/
or bit may be damaged.
5
EN
14.6.2017 . 9:41:13