Herunterladen Diese Seite drucken

Safety Notice - Vitavia HELENA 7000 Montageanleitung

Vorschau ausblenden Andere Handbücher für HELENA 7000:

Werbung

7b. SIde glazINg
Press glazing seal (7382) into the top groove
in each (7381) and cut to fit both ends.
If glazing with 4mm glass, press glazing seal
(6090) onto the aluminium profiles (7b.2) and
cut to length. Note - On all horizontal glazing
guides it is recommended to use smaller
lengths of the seal (6090) in the middle of
each field. This will allow condense water
which collects inside the house to escape.
Note - With Polycarbonate the glazing rubber
is not required.
Through the positioning of the (7050) bolt
head in the different guides in the glazing
capping's, it is possible to glaze the green-
house with 4mm,10mm or 16mm panes (7b.2).
Prepare bolts (7050) in each glazing capping
as shown (7b.3).
For 10mm glazing prepare 1 spacer (7407), in
the middle / top of each pane A (7b.4).
Position each glazing pane A into the frame
and connect the vertical capping's (7372),
(7373) or (7374) loosely with nuts (7053).
Lift pane A 15mm and connect capping's
(7381) loosely under the pane.
Note - The bolts (7050) used to hold the
diagonal braces in sections 1, 2 and 3 should
be replaced at this point (7b.8).
For 10mm glazing prepare 4 spacers (7409)
onto each (7321) and (7322) (2 spacers for
each pane E and F) (7b.5) (7b.6).
Position panes E and F.
Connect capping's (7377) or (7378) and then
(7375) / (7379) or (7376) / (7380) loosely.
Tighten all nuts. Please do not over tighten.
Note - The vertical capping's can be best as-
sembled when the bottom bolt is first inserted
into the hole, then the middle and finally the
top bolt. Ensure that the capping remains in
contact with the sill bar.
8. FINal StePS
Insert eave plastic (7370) and (7371) into both
ends of the eave bar (7324 - 7327) (8.1).
Note - It can help to pull the eave bar at the
top edge, carefully away from the house so
that the opening for the plastic becomes lar-
ger.
Take a drill not larger then ø25mm and make
a hole in the marked area inside parts (7370)
and (7371) (8.2).
Insert cropped head bolt (1412) into the bolt
channel at the bottom of corner bar (7310) and
connect parts (1405) and (1409) with alumini-
um nut (1002) on both sides (8.3). Fit elbow
8
(1402) onto the bottom of down pipe (1415)
(8.6) and then connect this to the eave plastic
(7370) or (7371) (8.11). Fit the down pipe
clamp (1403) around the down pipe and con-
nect to (1409) (8.4). Insert screw (1006) to fix
the down pipe in place (8.5).
Slide the roof vent into the correct section from
one end of the house (8.7). Attach the roof
vent fixer (7369) using the prepared holes and
self-drilling screw (7349) on both sides of the
roof vent (8.8) (8.9).
Assemble door track (7359) into the door ope-
ning. Connect to (7321), (7322) or (7324 -
7327) by inserting bolts (7052) into the bolt
channel on the outside of these bars and con-
nect with nuts (7053) (8.10).
Include at both ends of door track bar (7359)
bolt (7052) from outside and nut (3002) inside
the door guide to prevent the door from sliding
out of the track (8.10) (8.11).
Position the doors by inserting the plastic door
guides (2271) into the guide in door track bar
(7359) (8.12) (8.13a) and then lower the
wheels onto the door track on bar (7351)
(8.13b). Hook the door jump clips (7350) under
the lip on (7351) and tighten the lock nuts
(7360) (8.13b).
Connect plastic nut caps (6070) by pushing
them onto all visible nuts (7053) inside the
building (8.14).
Note - It is recommended to include a bead of
neutral silicone between the ridge bar and wall
from outside (8.9b). Neutral silicone is not
provided.
FINIShINg
If desired, it is possible to further seal the
greenhouse at the edges using neutral silicone.
Silicone is not included for this purpose.
Place the warning label inside the house.
Please check the tightness of all nuts and
bolts 2 weeks after completing the assembly.
A full range of greenhouse accessories, to
help you make the most of this product, is
available from your stockist. Please inform
yourself as to the possibilities.

SaFety NotIce

In the event of high wind conditions, close the
doors and all vents.
In the event of heavy snowfall, clear the roof of
the building or take suitable measures to sup-
port the roof. Heat the building in winter.
commeNtS
For the complete protection of your new
green house, we advise you to include it in
your house insurance. Please take note of
possible building rules relating to the positio-
ning of greenhouses.
Please stick the included greenhouse model
label onto door bar (7352) or (7353) after
success fully assembling this product. This
information is important in the event that re-
placement parts are later required.
Please keep these assembly instructions in a
safe place, for future reference!
Our policy is one of continuous improvement
and we reserve the right to change the specifi-
cations without prior notice.
036.01.1301

Werbung

loading

Diese Anleitung auch für:

Helena 8600Helena 10200Helena 11900