Important Safety Information - Hantech 1030586611 Bedienungsanleitung

EN
Read carefully before attempting to assemble, install, operate or maintain the product
described. Protect yourself and other by observing all safety information. Failure to
comply with instructions could result in personal injury and/or property damage.

IMPORTANT SAFETY INFORMATION

1. Read all instructions carefully before using the FAN.
2. Use this FAN only as described in this manual. Any other use not recommended by
the manufacturer may cause fire, electrical shock, or injury to persons.
3. Remove the package and ensure that the FAN is undamaged. In case of doubt do not
use FAN and contact with your supplier.
4. Don not let children play parts of package.
5. Before use the FAN, check if the voltage marked on the rating label corresponds to
the mains in your home.
6. Extreme caution is necessary when the FAN is used by or near children or Invalids
and whenever the FAN is left operating unattended.
7. Avoid using extension cord as the extension cord may overheat and cause a risk of
fire.
8. Do not pull the power cord to disconnect with power source. Always grasp the plug to
pull out.
9. Do not insert any objects into the FAN as it may cause an electric shock or injure or
damage to the FAN. Do not block or tamper with the FAN in any manner while it is
in operation.
10. Do not leave the FAN unattended. Always unplug FAN when not in use.
11. This FAN is not intended for use in wet or damp locations. Never locate a FAN where
it may fall into a bathtub or other water container.
12. Do not use FAN outdoors.
13. Disconnect the fan from the mains power when not in use, and before servicing or
performing any maintenance.
WARNING :The Main Power Switch and the On/Off switch should not be used as
the sole means of disconnecting power. Always unplug the power cord before
servicing or moving the unit.
14. Always disconnect the fan from the power supply when moving it from one location
to another.
15. Keep the fan clean and maintain in good condition (use an authorized service agent).
16. Use recommended parts only (non genuine parts may be dangerous, and will
invalidate your warranty).
17. When not in use store in a safe, dry, childproof location.
18. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by children without
supervision.
33
WARNING
To avoid danger of electric shock, unplug from outlet when not in use and before
cleaning. If the supply cord is damaged, it must be replaced by the manufactory
or it's service agent or a similarity qualified person in order to avoid a hazard.
ASSEMBLY INSTRUCTIONS (See Figure 1 & 2)
NOTE: Make sure you remove all contents from the package. Please check packaging
materials for parts that could be required to operate your fan.
1. Assemble base halves around power cord. To secure the base halves together, slide
the posts of one base half into the slots of the second base half. Refer to Figure 2.
2. Line up the screws holes of the base halves with the holes located on the bottom of
the fan housing. Secure with the six screws included with the product. Refer to
Figure 2.
3. Secure power cord as shown in Figure 2.
4. Turn fan right side up and place on a dry and level surface.
Figure 1
A
D
E
B
A. Control Panel
B. Fan Housing
C
C. Base Halves
D. Remote Control
Storage
E. Remote Control
OPERATING INSTRUCTIONS: (See Figure 3)
1. Plug the cord into a standard outlet.
2. To turn the fan on, press the power button
control.
3. Press the speed button to cycle through the speed settings in sequence. The
corresponding indicator light will illuminate to confirm the select on:
4. To turn the oscillation on and off, press the oscillation button
control panel or remote control. The oscillation icon
display.
34
Figure 2
C
D
Power Cord
located on the control panel or remote
located on the
will illuminate on the LCD