Team International EXP 7 Gebrauchsanleitung Seite 16

Fax +32 2 359 95 50

middle of the appliance, do not switch on the appliance, but take the filter holder out of
the espresso machine and try to put it into the right position again (as mentioned above).
 Put one cup under the opening of the filter holder.
 Make sure that the switches are in the OFF position.
 Now press the On/Off switch (7). The button will stay down in its "pressed" position and the
power light will burn indicating that the appliance is warming up.
 Wait until the control light of the espresso function
pump button (3). The control light of the pump will burn. The pump will switch on and after
a few seconds the coffee will flow out of the openings of the filter holder. At the beginning
you can hear that the pump will make more noise than when the water starts flowing. This
is absolutely normal.
 When the cup is filled, press the pump button again and the water will stop flowing.
 To make other espressos, empty the filter. Therefore you have to remove the filter holder
by turning it to the left. CAUTION: Be careful when you remove the filter holder (19)
because the metal parts may be hot. Never remove the filter holder (19) when the pump
button, steam function button and/or the switches are turned on. There might be some hot
water left under the creamer disk (18); be aware of this and don't get burned.
 Rinse the accessories with clear water and put a new coffee pad into the filter.
 Proceed as described here above.
Remarks:
 When using the appliance for the first time of after a long period of non-use, it is
recommended to let run through the hydraulic system at least one cup of water. Place
one cup under the steam pipe (10), turn the steam control knob anti-clockwise and press
the pump button (3). Water will come out of the steam pipe. As soon as the cup is filled,
press the pump button (3) again and turn the steam control knob (1) clockwise till the end.
Then make your espresso as described above.
 If you cannot remove the filter holder because of the pressure, let off steam by turning the
steam control knob anti-clockwise. Then try again.
HOW TO PREPARE A CAPPUCCINO
 First of all prepare a coffee as described above letting enough space in the cup for the
milk.
Caution: Before using the cappuccino function, make sure the filter holder has been removed
from its support.
In order to obtain thick and creamy milk froth it is necessary to evacuate the remaining water
in the hydraulic circuit of the appliance.
 Turn on the appliance with the On/Off switch (7).
 Let the steam knob (3) in OFF position, swing the steam pipe (10) to the right and put a
recipient under the steam pipe.
 Press the steam function button (5). A little water or steam might escape while the
appliance is warming up. This is absolutely normal. As soon as the control light of the steam
function
knob (1) anti-clockwise. The superfluous water will flow in the recipient and a strong steam
spurt will follow. Turn the Steam control knob clockwise to stop the steam spurt.
 Then fill the desired milk quantity into a heat resistant container (it has to be large enough
to avoid splashing, do not fill more than half of the recipient) and place it under the steam
pipe. Immerse the steam nozzle completely in the milk in order to avoid splashing. We
recommend you to use semi-skimmed cold milk only; do not use hot milk.
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don't change the page numbering. Keep the
language integrity.
(6) turns on, put a recipient under the steam pipe and turn the steam control
Assembly page 16/60
(6) burns. Wenn it is on, press the
16
TEAM EXP 7 - 070125