Werbung
ΕΛΛΗΝΙΚΑ
Οδηγός αντιµετώπισης προβληµάτων
----------------------------------------------------
Πριν αναζητήσετε τεχνική υποστήριξη για
κάποιο πρόβληµα, παρακαλούµε ελένξ τε τα
παρακάτω:
Πρόβληµα
Πιθανή Αιτία
Ο απορροφητήρας δεν λειτουργεί.
Το καλώδιο δεν είναι συνδεδεµένο.
∆εν υπάρχει ρεύµα στην πρίζα.
Η απορρόφηση δεν είναι ικανοποιητική.
Τα φίλτρα έχουν γεµίσει λίπη.
Ο
σωλήνας
εξαγωγής
βουλώσει.
Απαράδεκτος σωλήνας εξαγωγής,
πχ ∅ < 12,5cm, σταθερές περσίδες
στον εξωτερικό τοίχο, κλπ.
Οι λαµπτήρες δεν ανάβουν.
Έχουν καεί.
Έχουν ξεβιδωθεί.
Küppersbusch διατηρεί το δικαίωµα να εισαγάγει στις συσκευές της τις διορθώσεις τις οποίες
κρίνει αναγκαίες ή χρήσιµες χωρίς να αλλοιώνει τα βασικά τους χαρακτηριστικά.
Επίλυση
Συνδέστε το καλώδιο στην παροχή
ρεύµατος.
Ελένξτε/επισκευάστε την πρίζα.
Καθαρίστε
ή
αντικαταστήσετε
φίλτρα.
έχει
Ξεβουλώστε τον σωλήνα εξαγωγής.
Επικοινωνήστε µε τον τοποθέτη και
ακολουθείστε
τις
οδηγίες
εγκατάστασης από αυτό το φυλλάδιο.
Αντικαταστήστε τους.
Σφίξτε τους.
Notes: cleaning in the dishwasher with
aggressive detergents may blacken the
surface
of
metallic
parts,
affecting its gas retaining properties.
N.B. The filter must be cleaned at least once
a month depending on how often the
extractor is used. It must be remembered
that grease is deposited in the extractor
when cooking, whether it is switched on or
not.
Cleaning of the extractor body
The use of warm (40ºC approx.) soapy water
is recommended. A cloth moistened in this
water is used for cleaning the extractor,
paying
special
attention
Afterwards, dry it using a lint-free cloth.
Note:
Never use metallic scouring pads or
abrasive products that could damage the
surface.
τα
Do not use scrapers with metallic surfaces
such as knives, scissors etc.
Activated charcoal filter
To
install
the
charcoal
necessary to firstly remove the metallic
grease filters.
In order to fix them they will be coincide
the later sideburns of each filter in the
anchorage anticipated for it in the security
grid doing them to tilt upwards until its
fixation with the frontal eyelash of the
same one (Fig.6).
The carbon filters last from three to six
months
depending
conditions of use.
The activated carbon filters can neither be
washed nor regenerated. Once they are
exhausted, they must be changed
To replace used filters with new ones,
withdraw the old ones in the reverse order
.
to that of installation
Changing Bulbs
Firstly it is important that the mains are
disconnected, and ensure the bulbs that
are to be replaced are not hot.
Remove the light lens to expose the
extractable lamps.
The maximum bulbs power is 20W.
Technical Information
---------------------------------------------------
without
this
Dimensions
Electrical characteristics:
REFER TO RATING PLATE
Installation
---------------------------------------------------
To fix the cooker hood please choose one of
the following options:
a) Fixing to the upper part of the furniture
Figure 3 must be used where the position
to
the
grids.
of the holes is indicated.
b) To the internal side of the furniture
(without brackets):
When the body hood fits within the
furniture, fasten with two screws on each
side from the inside of the body hood,
using their side holes.
c) Fixing to the internal laterals of the
furniture (with brackets):
filters
it
is
1.- Screw two screws to each side of the
furniture
interior
instructions (A or B depending on the
width of the furniture). Leave them 3 mm
loose for adjustment.
2.- Screw the provided brackets to the top
part of the hood, keeping the internal
furniture width.
3.- Hold and rise the hood until the slots of
their brackets fit in the screws (step 1) of
on
the
particular
the furniture.
4.- Keeping the appliance hold, push it
towards furniture's bottom until screws fits
into a stable position inside the slots.
.
5.- Rise the hood a little until a definitive
position is obtained and tight the loosen
four screws to the brackets.
The lower part of the extractor must be
installed a minimum height of 60 cm
above the hob for electric cookers and 65
cm for gas cookers. (If the installation
instructions of a gas cooker indicate a
greater distance this must be observed).
(Fig. 3)
Width = 600//900 mm
Depth = 300 mm
Height = 343 mm
(Fig. 7)
following
figure
5
Werbung
