Safety Instructions For All Operations - Ryobi EAG600RS Bedienungsanleitung

GB
FR DE ES
DESCRIPTION
1. On/off switch
2. Spindle lock button
3. Grinding wheel
4. Wheel guard
5. Auxiliary handle
6. Clamp nut
7. Disc fl ange
8. Spindle shaft
9. Wheel guard lock screw
10. Wrench

SAFETY INSTRUCTIONS FOR ALL OPERATIONS

SAFETY WARNINGS
OPERATIONS:
a. This power tool is intended to function as
a grinder tool. Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, fi re and/or serious injury.
b. Operations such as sanding, wire brushing,
polishing or cutting-off are not recommended
to be performed with this power tool. Operations
for which the power tool was not designed may
create a hazard and cause personal injury.
c. Do not use accessories which are not
specifically designed and recommended by the
tool manufacturer. Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
d. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fl y apart.
e. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
f. The arbour size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbour holes that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad
for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage
or install an undamaged accessory. After
IT NL PT DK SE
COMMON FOR GRINDING
FI NO RU PL CZ
English
inspecting
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
h. Wear
Depending
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors,
capable
workpiece fragments. The eye protection must
be capable of stopping fl ying debris generated by
various operations. The dust mask or respirator
must be capable of fi ltrating particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
i. Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken accessory
may fl y away and cause injury beyond immediate
area of operation.
j. Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and shock the operator.
k. Position the cord clear of the spinning
accessory. If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled
into the spinning accessory.
l. Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and pull
the power tool out of your control.
m. Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
n. Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
o. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
p. Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
1
HU RO LV LT EE
and installing
personal protective
on application,
gloves and
of stopping
HR SI SK GR TR
an accessory,
equipment.
use face
workshop apron
small abrasive or