Herunterladen Inhalt Inhalt Diese Seite drucken

RedHotDot MMAX9 Bedienungsanleitung Seite 2

Welding machine
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

MMAX9
TECHNICAL SPECIFICATIONS / TECHNISCHE DATEN / ТЕХНИЧЕСКИЕ СПЕЦИФИКАЦИИ
Primary / Primär / Первичная цепь
Power supply voltage / Stromversorgung / Напряжение питания
Mains frequency / Netzfrequenz / Частота сети
Fuse / Sicherung / Плавкий предохранитель
Secondary / Sekundär / Вторичная цепь
No load voltage / Leerlaufspannung / Напряжение холостого хода
Manual striking system's maximum voltage (EN60974-3) /
Spitzenspannung des manuellen Startgerätes (EN60974-3) /
Пиковое напряжение механизма ручного поджига (EN60974-3)
Normal current output (I
) / nominaler Ausgangsstrom (I
2
Номинальный выходной ток (I
Conventional voltage output (U
(U
) / Допустимое выходное напряжение (U
2
Duty cycle at 40°C (10 min)*
Standard EN60974-1.
Einschaltdauer @ 40°C (10 min)*
Norma EN60974-1
ПВ% при 40°C (10 мин)*
Норма EN60974-1
Functionning temperature / Betriebstemperatur / Рабочая
температура
Storage temperature / Lagerungstemperatur / Температура хранения
Protection level / Schutzgrad / Степень защиты
Dimensions (Lxlxh) / Abmessung (LxBxH) / Размеры (ДхШхВ)
Weight / Gewicht / Вес
*The duty cycles are measured according to standard EN60974-1 à 40°C and on a 10 min cycle.
While under intensive use (> to duty cycle) the thermal protection can turn on, in that case, the arc swictes off and the
indicator switches on.
Keep the machine's power supply on to enable cooling until thermal protection cancellation.
The welding power source describes an external drooping characteristic.
*Einschaltdauer gemäß EN60974-1 (10 Minuten - 40°C).
Bei sehr intensivem Gebrauch (>Einschaltdauer) kann der Thermoschutz ausgelöst werden. In diesem Fall wird der
Lichtbogen abgeschaltet und die entsprechende Warnung erscheint auf der Anzeige. Das Gerät zum Abkühlen nicht
ausschalten und laufen lassen bis das Gerät wieder bereit ist.
Das Gerät entspricht in seiner Charakteristik einer Spannungsquelle mit fallender Kennlinie.
* ПВ% указаны по норме EN60974-1 при 40°C и для 10-минутного цикла.
При интенсивном использовании (> ПВ%) может включиться тепловая защита. В этом случае дуга погаснет и
загорится индикатор .
Оставьте аппарат подключенным к питанию, чтобы он остыл до полной отмены защиты.
Источник сварочного тока описывает падающую внешнюю характеристику.
) /
2
)
2
) / entsprechende Arbeitsspannung
2
)
2
Imax
60%
100%
2
110V – 240V (Nominal)
50 / 60 Hz
16A
MMA
TIG
MMA
72V
9kV
10
10
10
200A
200A
130A
20.4
10.4
20.4
28V
18V
25.2V
22%
27%
39%
120А
140А
80А
-10°C +40°C
-25°C +55°C
IP21
27 x 21 x 14 cm
5.5 kg
20A
TIG
10
130A
10.4
15.2V
58%
100А

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis