Herunterladen Inhalt Inhalt Diese Seite drucken

Wartung; Maintenance - Sartorius 16692 Betriebsanleitung

Membran-vakuumpumpen
Vorschau ausblenden Andere Handbücher für 16692:
Inhaltsverzeichnis

Werbung

3. Wartung

Die Membran-Vakuumpumpe bedarf keiner
regelmäßigen Wartung. Die Kugel lager sind
überdimensioniert und die Füllung mit
einem Spezialfett reicht aus für die
Gesamt lebensdauer des Gerätes. Membrane
und Ventile sind die einzigen Verschleißteile.
Das Auswechseln dieser Bauelemente
erfordert jedoch keine besonderen
technischen Kennt nisse und lässt sich in
wenigen Minuten am Standort der Pumpe
durchführen.
3.1 Auswechseln der Membrane (s. Abb.1).
3.1.1 Kennzeichnen Sie die Stellung des
Membrankopfes (8) zum Gehäuse (5) mit
einem Bleistift.
3.1.2 Lösen Sie die 4 Inbusschrauben (9)
und nehmen Sie den Membrankopf ab.
3.1.3 Nun lösen Sie die Senkschraube
und nehmen nacheinander Druckscheibe,
Zahnscheibe und Membrane ab.
3.1.4 Entfernen Sie die Lüfterhaube (4)
des Motors auf der rechten Geräteseite (2
Schrauben) und drehen Sie den Lüfterflügel,
bis das Pleuel in Mittelstellung ist. Legen Sie
dann die neue Membrane ein.
3.1.5 Auf die Membrane legen Sie nun erst
die Druckscheibe mit der flachen Seite nach
unten und dann passend die Zahnscheibe.
Ziehen Sie die Senkschraube gefühlvoll, aber
fest an.
3.1.6 Setzen Sie nun den Membrankopf (8)
wieder in die gekennzeichnete Position und
ziehen Sie die Inbusschrauben (9) über
Kreuz gleichmäßig an.
3.1.7 Kontrollieren Sie den leichten Lauf,
indem Sie den Lüfterflügel einmal ganz
herumdrehen und schrauben Sie die
Lüfter haube (4) wieder an.

3. Maintenance

The Sartorius Diaphragm Vacuum Pump
does not require regular maintenance. The
ball bearings are oversized and sufficiently
lubricated with a special grease to last
for the pump's entire service life. The
diaphragms and valves are the only parts
subject to wear. However, changing these
parts does not require any special technical
expertise and can be easily done on-site
within a few minutes.
3.1 Changing the Diaphragm (see Fig.1).
3.1.1 Use a pencil to mark the position
of the diaphragm head (8) in relation to
the housing (5).
3.1.2 Untighten the 4 Allen screws (9), and
remove the diaphragm head.
3.1.3 Now loosen the countersunk screw,
and remove the retainer plate, star lock
washer and diaphragm one by one.
3.1.4 Remove the end cover plate (4) for
the motor fan from the right side of the
pump (remove the 2 screws) and turn the
disk flywheel until the connecting rod is
in mid-position. Next, install the new
diaphragm.
3.1.5 Now replace the retainer plate first
with the flat side facedown on the
diaphragm followed by the star lock washer,
making sure that it is properly aligned.
Carefully but securely tighten the
countersunk screw.
3.1.6 Next, replace the diaphragm head (8)
in the marked position and uniformly
tighten the Allen screws (9) in opposite
diagonal pairs.
3.1.7 Check that the pump runs smoothly by
rotating the disk flywheel one complete turn
and then replace the end cover plate (4).
| 5

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

16695

Inhaltsverzeichnis