Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installation
Please pay attention to the information in the chapter "Preparations for installa-
tion"!
• First remove the cover (2) by rotating it
slightly counter-clockwise ("OPEN").
• Remove the mounting plate (5) from under-
neath the casing (3). To do this, carefully
pull the strap.
Since there are five contact pins in the
corresponding sockets, the removal of the
mounting place (5) requires a certain ef-
fort. However, do not use force.
Due to the design used, both the attach-
ment of the motion detector and the con-
nection of all cables are very easy.
• Pass the connection cable(s) through the
rubber seal in the mounting plate (5).
• Fasten the mounting plate (5) with two
screws (4) and plugs (7) to the ceiling.
Depending on the surface suitable screws
and plugs are to be used!
Place the sealing washer (6) provided bet-
ween mounting plate and surface other-
wise a protection according to IP44 is not
guaranteed.
If the motion detector is to be mounted on
a vertical wall, pay attention to the marking
" UP" on the mounting plate (5) and the
housing (3)! The marking must point up-
wards vertically.
• Tighten the connection cables in the
screw terminals of the mounting plate. For
this purpose, observe the information and
illustrations in chapter "Connection".
• Place the housing (3) with the contact pins on the mounting plate (5) observing the correct
orientation.
Attach the casing (3) to the mounting plate (5), using the two supplied small screws.
• After adjusting the settings for on-time, sensitivity and brightness adjustment (see chap-
ter "Controls on the motion detector"), attach the cover (2). Lock it by rotating it slightly in
clockwise direction until it clicks into place.
• To limit the detection range, the cover (1) included in the delivery can be attached. By
excluding some areas accordingly, the detection range can be adjusted.
Connection
Connect the connection cables with the
corres-ponding screw terminals (ob-
serve labels):
L = Phase
N = Neutral wire
L´ = Switching output of relay 1
D1/D2 = potential-free switching con-
tacts of relay 2
Please observe the wiring diagram (for
two lights) in the picture on the right.
Do not connect the connections inside
the motion detector but use an external
junction box, otherwise the screw ter-
minals might be overloaded (see illust-
ration at the bottom right).
An exterior light can be controlled via the relay switching output L´. The second
relay for the switching output D1/D2 may be used for a second light.
For example, to control a staircase switch, the switching output is set to a very
short switching time of approx. 1 second (turn the control dial "TIME1" complete-
ly to the left to the position "
" by rotating it counter-clockwise).
Controls on the motion detector
• Setting the on-time for output D1/D2 (control dial "TIME2")
This control dial allows setting the time for the on-time of output D1/D2. Turning the con-
trol dial counter-clockwise shortens the on-time, turning it clockwise lengthens it. A set-
ting of 1 minute (position "1") up to 2 hours (position "2H") is possible.
If new motion is detected during the on-time, the time for the on-time starts again.
• Setting the on-time for connection L´ (control dial "TIME1")
Using this control dial, you can set the time for the on-time of the relay for the connection
L´. Turning the control knob counter-clockwise shortens the on-time, turning it clockwise
lengthens it. There is a setting of 1 second (position "
tes (position "30S" to position "30") which can be used.
If new motion is detected during the on-time, the time for the on-time starts again.
• Setting the brightness adjustment (control dial "LUX")
This control dial allows setting the switching threshold from which ambient brightness
the motion detector is activated.
Turning the control dial to the left in direction of the moon symbol activates the motion
detector only with great darkness, turning it to the right in direction of the sun symbol
activates the motion detector in brighter conditions. The position "TEST" is used to check
the detection range (on-time of the relays in the motion detector is approx. 3 seconds).
• Setting the sensitivity (control dial "SENS")
This control dial is used to set the level of changes in temperature from which a switching
process is triggered.
When turning it left the motion detector will activate already with low changes in tempe-
rature, turning it to the right will only activate it with higher changes in temperature.
Maintenance and care
The motion detector is maintenance free, this is why you should never open it or take it apart
(aside from the installation described in this operating instruction). Maintenance or repairs
may only be performed by qualified personnel.
Clean the hemispherical diffusing panel of the motion detector occasionally from dust or
sediments, by only using a dry, clean and soft cloth.
Disposal
Do not throw this product into the household garbage.
Dispose of an unserviceable product in line with the relevant statutory regulati-
ons.
Technical data
Operating voltage.........................................220 - 240 V/AC, 50 Hz
Power consumption.....................................max. 2 W
Switching capacity of Connection L' ........2200 W (resistive load)
.........................................................................1200 W (inductive load)
Switching capacity of connection D1/D2 ..1000 W (resistive load)
DC load...........................................................Only on output D1/D2, with 30 V/DC max. 10 A (300 W)
Devices with mainly resistive load are e.g. light bulbs, heaters etc.
Devices with inductive load are e.g. engines, control gears, conventional trans-
formers, energy saving light sources etc.
On-time of connection L' ............................. 1 second for the "
On-time of connection D1/D2 .....................1 minute to 2 hours
Mounting location ........................................Wall and ceiling mounting
Protection class ........................................... IP44 (observe mounting location, see chapter "In-
Viewing angle ...............................................360°
PIR range .......................................................Max. approx. 8 m (at ambient temperature +20 °C)
.........................................................................with mounting height 2.4 m
Mounting height ...........................................2.4 to 3 m is recommended
Ambient brightness......................................adjustable, 5 lux to 1000 lux, test mode
Dimensions (Ø x h) .......................................140 x 68 mm
Weight ............................................................approx. 235 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
") or 30 seconds up to 30 minu-
" position or 30 seconds up
to 30 minutes
stallation")
Werbung
Inhaltsverzeichnis
