Troubleshooting - Steinbach Speedcleaner RX5 Bedienungsanleitung

EN
K: Cleaning roller
L: Power cable
Preparation
Place the cleaner into the water, while holding onto the hanging ring
(Fig, 5). Once all the air has escaped from the cleaner (Fig, 6), (the
cleaner must be completely free of air, otherwise normal operation
will be affected), it will sink to the bottom on its own.
Caution: For optimal performance, make sure that there is no more
air in the cleaner (air bubbles stop coming out of the cleaner, and it
stays on the pool floor properly).
Connecting the power source
When the cleaner is completely on the pool floor (Fig. 8-10), take the
power cable, roll it out fully and push the plug into the socket on the
electricity control box. Then connect the cable to the socket (Please
note when connecting cables that the plugs are in the right direction
and position in relation to each other), and tighten the nuts on both
sides. Connect the mains cable to the power source. The swimming
pool cleaner is now ready for use.
Starting automatic operation, figure 11
Press the ON/OFF button to turn on the operating unit. Select the de-
sired cleaning time by pressing the CYCLE button. The automatic pool
cleaner will immediately start cleaning your pool and will turn off once
the selected cleaning time has elapsed.
Warning
Caution: Before removing the cleaner from
the pool, make sure that the electricity is fully
switched off.
Preparation
Care and maintenance
The cleaner turns itself off automatically after a cleaning cycle. Unplug
the mains cable, gently pull the cable, and lift the cleaner out of the
water using the ring on the clamp nut.
Caution:
When lifting the cleaner out of the water, you must ensure that the
cleaner does not hit the side of the pool wall, otherwise you may dam-
age both the cleaner and the liner.
Before the cleaner clears the surface of the water, it must be held
there for 10 to 15 seconds, so that most of the water can flow out of
the water outlet into the pool. Only then should you put the cleaner on
the edge of the swimming pool. Fig. 12
It is important to place the cleaner near the edge of the pool, then
open the cover screws and remove the housing cover. Now take out
the filter unit and remove the filter bag.
When cleaning the filter bag, you must remove the dirt from the out-
side of the bag with clean water. Fig. 14. Then put the bag back in. As
a water outlet with filter is built into the cleaner, some dirt may remain
in the cleaner, which should also be rinsed out. Then you should put
the filter unit back in completely along the motor.
Caution: There is a positioning pin on the top of the filter housing,
please do not mount this incorrectly! Fig. 15.
Page 6 of 46
After mounting the housing cover, the cover screws must be re-fitted.
Caution: To avoid any negative effect on the performance of the
cleaner, make sure that the cover is properly attached to the base
housing. To avoid any damage, please make sure that the cable is in
the correct position. Fig. 16.
Hints and tips
Every time the cleaner is taken out of the water, the filter cleaner must
be cleaned.
Make sure the pH value of the water is between 7.0 and 7.2.
Make sure the water temperature is between 12°C and 32°C.
After every clean, the drive train must be thoroughly cleaned to en-
sure the same level of grip on the next clean.
After pressing the "Power Off" button, the "Power On" button cannot
be pressed for 30 seconds.
We recommend keeping the cleaner between 5°C and 40°C in a
shaded, well ventilated place. The mains cable should be coiled
around the cable holder for storage. (The floats must not be pushed
along the cable to ensure the cable floats properly in the water.) Avoid
direct sunlight at all times.
We recommend attaching the operating unit with a safety rope, to
avoid any risk of the power pack being pulled into the pool.
Before use, please read the instructions relating to trouble-shooting
thoroughly.
Instructions for mounting the 4 locking plates on the cover
For pools with steps we recommend fitting locking plates to the cover.
These locking plates stop the cleaner from tipping.
Attach the stabiliser as shown in the photo. Fig. 22
Screw the screw in through the hole in the cover and tighten. Fig. 23.
Tighten the stabiliser with a Philips screwdriver.
Trouble shooting
Fault Cause
The power ca- Cable was not re-
ble is twisted leased properly
or tangled
The cable in the wa-
ter is too long.
Cleaner is stuck on
the outlet grille
The cleaner The power unit is in
cannot reach the wrong place
all areas.
Water circulation in
the pool is switched
on.
Connection cable is
too short
Cleaner does Filter bag is blocked
not climb up
the pool wall
Algae is growing on
the walls
Water temperature is
too high / too low
Brushes are worn
Solution
Switch off the unit, re-
lease and uncoil the ca-
ble.
Remove the excess ca-
ble from the water.
Switch off the filter unit.
Position the power unit
so that the cleaner can
reach all areas properly.
Switch off the filter unit.
Place the greatest pos-
sible length of connect-
ing cable into the pool,
but bear in mind the cor-
responding minimum
distance between the
operating unit and the
pool
Replace the filter bag
Clean the pool walls
Optimal water tempera-
ture is between 10°C
and 32°C
Contact a dealer, re-
place the brushes
Speedcleaner RX5 | 2017_V1