Chicco I-Move Gebrauchsanleitung Seite 25

TRANSFORMABLE HOOD
A transformable hood can also be fitted on the stroller.
36. The seat has two fixtures on the sides of the backrest
which are used to fit the hood. To fit/remove the hood,
slide the clip-on system into the fixtures, as illustrated in
diagram 36.
37. Close the zip on the back of the seat (Diag. 37).
WARNING: The hood must be fitted correctly on both
sides of the stroller. Check that it is securely fastened.
38. To open the hood, press the front arch forwards and fas-
ten it in place using the side hinges, as seen in diagram 38.
39. To use it as a summer sun-hood, simply open the rear
zip (diagram 39 A) and adjust the hood to the desired posi-
tion (diag. 39B).
40. When the backrest is full reclined, it is possible to open
the zip on the back to expand the range of the hood and
guarantee extra protection (diag. 40A and 40B).
COMFORT KIT
The stroller can also be fitted with a Comfort Kit.
41. The Comfort Kit comes with 2 shoulder strap pads A, a
crotch strap cover B. (diagram 41).
42. Slide the shoulder pads onto the straps as seen in
diagram 42. The straps can be adjusted to suit the child's
height.
43. Slide the crotch strap into the slot in the material as
seen in diagram 43.
WARNING: the safety harness must always be fastened to
guarantee complete safety for your child.
RAINCOVER
A raincover can also be fitted onto the stroller.
44. Fit the raincover by fastening it to the hood using the
elasticated section at the top (diag 44A) and fix in place at-
taching the Velcro fasteners to the ends of the front frame
tubes, as illustrated in 44B. When you have finished using
it, allow it to dry properly (if it is wet) before you fold it
away.
WARNING: pay particular attention when using the rain-
cover.
WARNING: the raincover cannot be used on a stroller
which has no hood or sun-hood as it could suffocate the
child. When the raincover is fitted on the stroller, never
leave it exposed to direct sunlight with the child inside, as
the temperature will rise considerably.
SLEEP SACK / LEG COVER
The Stroller can be fitted with a baby sleep sack which can
also be used as a leg cover.
45. Start by removing the bumper bar, then place the baby
sleep sack on the seat. Slide the bumper bar through the
slots on the baby sleep sack and fasten it to the seat (diag.
45).
The sleep sack has a zip at the back to divide it into a mat-
tress and leg cover which can be used individually. The
standard sleep sack user instructions are the same when
used on the stroller.
CARRY-ALL BASKET
The stroller can be fitted with a practical carry-all basket.
46. To assemble the basket on the stroller, attach the velcro
fasteners, on the three ends of the basket, to the three slots
on the stroller (diagrams 46A and 46B); then thread the 2
straps, found on the top part, around the tube and fasten in
place as seen in diagrams 46A and 46C.
WARNING: Do not overload the basket with weights of
more than 2kg. You must remove all contents from the
basket before you close the stroller.
BAG
The stroller can also be fitted with a practical carry-all bag,
which includes a changing mat.
47. To make the bag even more practical, both the inside
and outside have lots of pockets and compartments which
can be used to store a number of different items in an or-
derly manner (diagram 47).
WARNING: do not overload the bag with weights of over
2 kg.
WARNING: exceeding this limit may compromise the sta-
bility of the stroller and cause it to topple over.
Important note: the images and instructions contained in
this handbook refer to one version of the stroller; some
components and functions described herein may vary ac-
cording to the version of the stroller you have purchased.
25