Bosch GSA 10,8 V-LI Professional Originalbetriebsanleitung Seite 14

OBJ_BUCH-1272-002.book Page 14 Thursday, August 18, 2011 8:25 AM
14 | English
Technical Data
Sabre saw
Article number
Rated voltage
Stroke rate at no load n
0
Tool holder
Stroke
Cutting depth, max.
– in wood
– in non-alloy steel
– Pipe diameter
Weight according to
EPTA-Procedure 01/2003
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 70 dB(A); Sound power level 81 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a =8.0 m/s , K=1.5 m/s
h
Cutting wooden beam: a =12.0 m/s
h
The values given for sawing particle board apply for a workpiece thick-
ness of 20 mm.
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
1 619 P09 831 | (18.8.11)
Dr. Egbert Schneider
Senior Vice President
GSA 10,8 V-LI
Engineering
Professional
3 601 F4L 9..
V= 10.8
-1
min 0 – 3000
Robert Bosch GmbH, Power Tools Division
SDS D-70745 Leinfelden-Echterdingen
Leinfelden, 18.08.2011
mm 14.5
Assembly
mm 65
mm 8
Battery Charging
mm 50
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
kg 1.2
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
2
,
2 2
, K=1.5 m/s .
tomatically switched off. The battery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Removing the Battery (see figure A)
– To remove the battery 11 press the unlocking buttons 5
and pull out the battery downwards. Do not exert any
force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
8 indicate the charge condition of the battery 11.
– Press the On/Off switch 7 halfway or completely through
to indicate the charge condition.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pressing the On/Off switch 7, the
battery is defective and must be replaced.
Dr. Eckerhard Strötgen
Head of Product
Certification
Do not continue to press the On/Off
WARNING
switch after the machine has been au-
Capacity
≥2/3
≥1/3
<1/3
Reserve
Bosch Power Tools