Technical Data - Grundig Elegance 63 ST 63-2103 DOLBY Servicehandbuch

SPECIAL SETTINGS
_____________________________________________________________________
Notes:
Repeat the automatic channel search until the channel desired appears.
Cancel the automatic channel search with »TXT«.
The colour and sound standards are allocated automatically.
6 Select the line » Name« with »P+« or »P-«, and confirm with »
Select the position required with » «, use »P+« or »P-« to select the letters or
Manual tuning
digits required, and confirm with »
Program 06
C/S Channel
Channel 34
Finetun. 00
7 To fine tune the picture (when necessary), select the line » Finetun.« with
Name RTL2
»P+« or »P-« and modify the fine tuning with » « or » «.
OK Memorize •Change TXT
8 Save the setting with »OK«.
Note:
To set further TV channels, repeat points
9 Complete the setting with »TXT«.
Resetting all TV channels
All the TV channels can be reset (e.g. when you move town).
Dialog Center
Language selection
Sleep Timer
1 Call up »Dialog Center« by pressing »
Child lock
Special functions
2
Select the line »Automatic Tuning System« with »P+« or »P-« and confirm
Sort
with »OK«.
Manual tuning
Automatic Tuning System
– The »Adjust country« menu will be blended in.
Service
OK TXT
3
Select a country with »P+« or »P-« and confirm with »OK«.
– The ATS search will start.
Adjusting colour standards manually
When the ATS search is used to set the TV channels, the colour standards are
allocated automatically. Do not carry out this setting if the colour is already well
adjusted on the various channels.
Service
Preset
1 Call up »Dialog Center« by pressing »
Color P 01 auto
IDP2 HP
Telet. language P 01 West
Service Code – – – –
2 Select the line »Service« with »P+« or »P-« and confirm with »OK«.
TXT
3
Select the line »Color« with »P+« or »P-« and select the colour standard
required with » « or » «.
4 Complete the setting with »TXT«.
Note:
The lines » IDP2« and » Service Code« are for the exclusive use of the author-
ised dealer.
Service
Factory settings
Preset
Color P 01 auto
IDP2 HP
All picture and sound values are preset at the factory. This pre-setting can be
Telet. language P 01 West
Service Code – – – –
called up via the »Service« menu.
TXT
1 Select » Preset« with »P+« or »P-«.
2 Confirm the pre-set values with »OK«.
20
F « (blue).
F « (blue).
3 to 8.
i «.
i «.
INFORMATIONEN

Technical data

Mains voltage:
Power requirement:
Final sound stage:
Frequency area:
Channel positions:
SAT:
Service notes for the authorised dealer
The TV set may only be operated using the mains cable set supplied. It prevents mains interference
and is an integral part of the appliance approval. For replacement purposes, please only order the
mains cable set with the designation "GWN 9.22/part number 8290.991-316" from an approved
service specialist.
The product conforms to the following RU guidelines:
73/23/EEC guideline on electrical equipment for use within certain voltage limits. 89/336/EEC
guideline on electromagnetic compatibility.
The appliance complies with the standards: EN 60065, EN 55013, EN 55020
Contact assignment for the EURO-AV (Scart) socket
Pin Signal
11 = Audio output right
20 2
12 = Audio input right
13 = Audio output left
14 = Audio earth
15 = Blue earth
16 = Audio input left
21 19 1
17 = RGB blue input
18 = Switching voltage
19 = Green earth
10 = –
11 = RGB green input
Additional Information for Units sold in Great Britain
Units sold in GB are suitable for operation from a 240 V AC, 50 Hz mains supply.
In case this appliance is supplied with a Safety Standard Approved mains lead fitted with a non-
rewireable 13 Amp mains plug which, if unsuitable for your socket, should be cut off and an appro-
priate plug fitted by a qualified electrician. The fuse and fuse holder must be removed from the plug
as accidental insertion of the redundant plug into a 13 Amp socket is likely to cause an electrical hazard.
Note:
The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13
Amp socket elsewhere.
If it is necessary to change the fuse in the non-rewireable plug, the correct type and rating (5 Amp
ASTA or BSI approved BS 1362) must be used and the fuse cover must be refitted. If the fuse cover is
lost or damaged the lead and plug must not be used until a replacement is obtained. Replacement
fuse covers should be obtained from your dealer.
If a non-rewireable plug or a rewireable 13 Amp (BS 1363) plug is used, it must be fitted with a 5
Amp ASTA or BSI approved BS 1362 fuse. If any other type of plug is used it must be protected by a
5 Amp fuse either in the plug or at the distribution board.
Important:
The wires in the mains lead are coloured in accordance with the following code:
BLUE – NEUTRAL, BROWN – LIVE
As the colours of the wires in the mains lead of your appliance may not correspond with the
coloured marking identifying the terminals in your plug, proceed as follows:
Connect the BLUE coloured wire to plug terminal marked with the letter "N" or coloured black.
Connect the BROWN coloured wire to the plug terminal marked with a letter "L" or coloured
red.
In no circumstance must any of the wires be connected to the terminal marked with a letter "E",
earth symbol , coloured green or green and yellow.
Replacement mains lead can be obtained from your dealer.
_________________________________________________________
220 – 240 V, 50/60 Hz,
(range of adjustment in the mains supply circuit 190 ... 264 V)
in operating mode 75 W, in standby mode 4 W
2x8 Watt music (2x4 Watt sine)
C01 ... C99, special channels S01 ... S41, frequencies band 1 ... 4
99 and 1 AV
The TVset can be retrofitted with SAT module SER 2100
Pin Signal
12 = –
13 = Red earth
14 = Earth
15 = RGB red input, (S-Video = Chroma)
16 = RGB switching voltage
17 = Video earth
18 = RGB switching voltage earth
19 = Video output
20 = Video input, (S-Video = Luminanz)
21 = Shield/earth
21