Texas A/S MPC 1500 Bedienungsanleitung Seite 10

will prevent blockage and ensure that there is airflow
through the engine.
When to use the aerator/scarfier roll
•
The aerator cylinder (blades) is used to aerate the
the lawn, providing more air to the roots of the
grass, so it can grow stronger and prevent moss.
•
The scarifier cylinder (springs) is used to remove
already existing moss in the lawn.
It is recommended to use both cylinders in combination
at least 2 times a year on your lawn: Spring and
autumn, and only when the ground is completely free of
frost.
Change of aerator roll
Replacing aerator cylinder (illustration 10-12):
1. Disconnect the power cord
2. Tilt the machine around on the side.
Unscrew the two screws ⒂ on the underside of the
3.
hosing using an allen key.
4. Lift the aerator cylinder
away from driver shaft.
Remove the bracket ⒄ from the earator cylinder ⒃
5.
Push the bracket ⒄ on to the new cylinder ⒃
6.
Push new aerator cylinder ⒃ on to the driver shaft.
7.
Fix the bracket ⒄ to the underside of the housing
8.
and tight the 2 screws ⒂ using the allen key without
tightening too much.
The scarfier cylinder ⒅ is fitted in the same way.
9.
Inspect the cylinders for damage, cracks or excessive
rust or corrosion. Replace is necessary.
Art. no. 428573 - complete aerator cylinder (blades)
Art. no. 428579 - complete scarifier cylinder (springs)
Art. no. 428575 - individual springs
Danger!
The aerator/scarifier cylinders can cause injuries!
Prior to inspecting faults, unplug the power cord and
wait until the cylinder has stopped rotating completely.
Wear working gloves when inspecting faults.
Storage and maintenance
Maintain your lawn raker
Check all bolts, screws, nuts and deck. Always make
sure that the cylinders are in good condition. Replace if
necessary.
Disconnect the power cord, and clean the cutting deck
from grass/moss after every use.
Store the lawn raker in a dry and clean room.
The engine must be completely cooled off
before storing indoor or covered !
Before long time storage, dip a cloth in oil and lubricate
the metal parts to prevent rust. Protect the machine
from frost by covering it with e.g. a blanket.
Loosen the handle bar fasterning knob ④ and ⑤, the
Foldable handlebar (illustration 9)
handle bar could be "Z" type folded.
Technical specifications
⒃ at an angle and pull
10
Model
Motor
Rotations per minut
Working width
Working depth
Grass catcher
Weight
Noise level
Vibration
Protection class
Warranty terms and conditions
The warranty period is 2 years for private end users in
EU countries.
Products sold for commercial use, only have a warranty
period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are
NOT covered by the warranty.
Wearing parts, which are NOT covered for more than
12 months:
•
Blades/springs
•
Cables
•
Belts
•
Fuses
•
Switches
•
Printed circuit boards (PCB)
The warranty does NOT cover damages/faults
caused by:
•
Lack of service and maintenance
•
Structural changes
•
Exposure to unusual external conditions
•
Damages to the bodywork, deck, handles etc.
•
If the machine has been improperly used or
overloaded
•
Use of unoriginal spare parts.
•
Other conditions where Texas cannot be held
responsible.
Whether a case is a warranty claim or not is
determined in each case by an authorized service
center.
Your receipt is your warranty note, why it should
always be kept safe.
Remember: The purchase of spare parts as well as
any request for warranty repair, model number, year
and serial number should always be informed.
It can be found on the CE-label on the machine.
*We reserve the right to change the conditions and
accept no liab ility for any misprints.
MPC1500
1500W / 230V ~ 50 Hz
4000 rpm (no-load)
32 cm
-12 ~ +5 mm
50 l.
15 kg
94 dB(A)
2
3.05 m/s
IPX4