Technical Data; Impact Drill - Bosch GSB Professional 21-2 RE Originalbetriebsanleitung

OBJ_DOKU-26857-001.fm Page 15 Thursday, May 26, 2011 3:57 PM
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen

Technical Data

Impact Drill

Article number
Rated power input
Output power
No-load speed
– 1st gear
– 2nd gear
Rated speed
– 1st gear
– 2nd gear
Impact frequency at no-load
Rated torque (1st/2nd gear)
Electronic torque control
Speed preselection
Constant electronic control
Right/left rotation
Key type drill chuck
Keyless drill chuck
Fully automatic spindle locking (Auto-lock)
Safety Clutch
Spindle collar dia.
Maximum drilling diameter (1st/2nd gear)
– Concrete
– Brickwork
– Steel
– Wood
Chuck clamping range
Weight according to EPTA-Procedure
01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Assembly
Before any work on the machine itself, pull the mains plug.
Auxiliary Handle (see figure A)
Operate your machine only with the auxiliary handle 11.
The auxiliary handle 11 can be set in 12 positions to achieve
a safe and low-fatigue working stance.
Bosch Power Tools
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
09.05.2011
GSB ... 21-2 21-2 RE
Professional
3 601 ... A9C 0.. A9C 5..
W 1100 1100
W 630
-1
min 900 0 – 900
-1
min 3000 0 – 3000
-1
min 580
-1
min 1900 1900
-1
min 51000 51000
Nm 9.6/3.2 9.6/3.2
–
–
–
–
–
–
mm 43
mm 22/13 22/13
mm 24/16 24/16
mm 16/8 16/8
mm 40/25 40/25
mm 1.5 – 13 1.5 – 13
kg 2.9
/II
Turn the bottom part of the auxiliary handle 11 in rotation di-
rection and push the auxiliary handle 11 forward until you
can pivot it to the desired position. Then pull the auxiliary han-
dle 11 back again and tighten it by turning the bottom part of
the auxiliary handle in rotation direction
Adjusting the Drilling Depth (see figure A)
The required drilling depth X can be set with the depth stop 12.
Press the button for the depth stop adjustment 10 and insert
the depth stop into the auxiliary handle 11.
English | 15
Dr. Eckerhard Strötgen
Head of Product
Certification
21-2 RE 21-2 RCT 21-2 RCT
A9C 6.. A9C 7..
1100 1300
630 630 695
0 – 900 0 – 900
0 – 3000 0 – 3000 0 – 3000
580 580 900
1900 3000
51000 51000
9.6/3.2 7.8/2.6
– –
– –
– –
–
–
43 43 43
22/13 22/13
24/16 24/16
16/8 16/10
40/25 40/25
1.5 – 13 1.5 – 13
2.9 2.9 2.9
/II /II /II
.
2 609 932 659 | (26.5.11)
A9C 8..
1300
695
0 – 900
900
3000
51000
7.8/2.6
–
–
43
22/13
24/16
16/10
40/25
1.5 – 13
2.9
/II