Service Test Programme; Keyboard Control Unit; Automatic System Test; Manual System Test - Grundig GDV 110 Bedienungsanleitung

Service Test Programme

Service Test Programme
GB
The Service Test Programme is divided into 3 different parts:

– Automatic System Test

– Manual System Test

– PC System Test
The basis of these System Tests are the Service Test Levels, which are
carried out automatically with the respective test or can be called up
manually.
1. Automatic System Test
With the Automatic System Test the hardware of the DVD-Player can
be checked without further equipment.
During the Automatic System Test the Service Test Levels, which are
listed in the table, are called and executed. If the DVD-Player is faulty,
"Error" is shown on the display and the Service Test Levels have to be
executed with the Manual System Test or the PC System Test.
Remark: With the Automatic System Test the A/V-MUX-board is not
tested.
Start of the Automatic System Test
Press 2 keys simultaneously
<OPEN/CLOSE> + <PAUSE>
Switch power ON
During the test, the display shows
the number of Levels
which have to be tested.
NO
SET OK
YES
To exit Automatic Systemtest, switch power OFF
Number Nucleus
on
display
6 PapChksFl
5 PapDramWrR
4 Papl2cDisp
3 PapS2bEcho
2 Papl2cNvram
1 CompSdramWrR
12
D V D
V C D
1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 +
D V D
V C D
1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 +
D V D
V C D
1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 +
Description
Calculate and verify checksum
FLASH memory
Pattern test of all locations in the
DRAM(s)
2
checks the I C interface with the
slave processor on the display PCB
Checks the I 2 C interface to the
drive mechanism
2
Checks the I C interface with the
NVRAM
Pattern test of all locations in the
SDRAM(s)
2. Manual System Test
The Manual System Test is a possibility to check which of the modules
(Keyboard Control Unit, Monoboard or Drive Mechanism) is faulty. In
addition to that, it is possible to check all ERRORS by reading the
ERROR log and the ERROR bits, including the ERRORS which have
appeared in the normal use of the DVD-Player. At the end of the
Manual System Test a Loop Test is started (the Service Test Levels of
the Automatic System Test are running in an endless loop).
For this test the DVD-Player has to be connected to a TV Set (PAL or
Multisystem), to control the results of the Service Test Levels.
To check the results of some Service Test Levels, the System Test
requires interactive actions from the user (e.g. confirmation of a
testpicture or a testsound). For some levels (e.g. levels for testing the
Drive Mechanism functions) the DVD-Player has to be opened to
control the function of the moveable components.
The test only checks functions, which can be checked by the Service
Test Software.
Start of the Manual System Test
Press 2 keys simultaneously
<OPEN/CLOSE> + <STOP>
Switch power ON
Interactive Test

Keyboard Control Unit

Display Test
LED Test
Keyboard Test
Remote Control Test
Digital Board
Picture Test 1
Sound Test
Basic Engine
Version Number
Tray Test
Sledge Test
Disc Motor Test
Focus Test
Radial Test
Jump Test
Tray Test
Error Log & -Bits
Loop Test
Switch power OFF to end
player test
2.1 Interactive Tests
2.1.1 Keyboard Control Unit
Display Test
Service Test Level: DispDisplay
By showing a series of test patterns on the local display, the local
display is tested. To step through all different patterns, the user must
either press PLAY (pattern is OK) or PAUSE (pattern was incorrect) to
proceed to the next pattern. The display of patterns is continued
cyclically manner until the user presses NEXT.
Note that a different sample pattern is used here to show all different
display patterns. All other pattern in this document are simplified for
essentials.
If the user presses NEXT before all display patterns are tested, it will
cause an error in the overall result of the System Test.
GDV 110
DispDisplay
DispLed
DispKeyb
DispRc
VideoColDencOn/Off
AudioSinOn
BeVer
BeTrayOut/In
BeSledgeOut/In
BeDiscMotorOn/Off
BeFocusOn/Off
BeRadialOn/Off
BeGroovesIn/Mid/Out
BeTrayOut/In
LogReadErr
LogReadbits
GRUNDIG Service